| View previous topic :: View next topic |
| Author |
Message |
APolozov
Apprentice
Joined: 28 Sep 2006
Posts: 194
Location: Voronezh, Russia
|
 Posted: Mon Nov 27, 2006 6:54 pm Post subject: Do not work PhotoCamera with SD-card |
 |
|
My photocamera HP PhotoSmart M407 not work as USB-Storage with pluged SD-card
and work without
This log with SD-card
| Quote: | kernel: ohci_hcd 0000:00:02.0: wakeup
kernel: usb 2-2: new full speed USB device using ohci_hcd and address 8
kernel: usb 2-2: configuration #1 chosen from 1 choice
kernel: scsi6 : SCSI emulation for USB Mass Storage devices
kernel: usb-storage: device found at 8
kernel: usb-storage: waiting for device to settle before scanning
kernel: Vendor: HP Model: PhotoSmart M407 Rev: No.1
kernel: Type: Direct-Access ANSI SCSI revision: 00
kernel: SCSI device sda: 248224 512-byte hdwr sectors (127 MB)
kernel: sda: Write Protect is off
kernel: sda: Mode Sense: 87 00 00 08
kernel: sda: assuming drive cache: write through
kernel: SCSI device sda: 248224 512-byte hdwr sectors (127 MB)
kernel: sda: Write Protect is off
kernel: sda: Mode Sense: 87 00 00 08
kernel: sda: assuming drive cache: write through
kernel: sda:
kernel: sd 6:0:0:0: Attached scsi removable disk sda
kernel: usb-storage: device scan complete
kernel: usb 2-2: reset full speed USB device using ohci_hcd and address 8
kernel: usb 2-2: reset full speed USB device using ohci_hcd and address 8
kernel: usb 2-2: USB disconnect, address 8
kernel: scsi 6:0:0:0: SCSI error: return code = 0x00010000
kernel: end_request: I/O error, dev sda, sector 248216
kernel: Buffer I/O error on device sda, logical block 31027
kernel: scsi 6:0:0:0: rejecting I/O to dead device
last message repeated 3 times
kernel: sda : READ CAPACITY failed.
kernel: sda : status=0, message=00, host=1, driver=00
kernel: sda : sense not available.
kernel: scsi 6:0:0:0: rejecting I/O to dead device
kernel: sda: Write Protect is off
kernel: sda: Mode Sense: 00 00 00 00
kernel: sda: assuming drive cache: write through
kernel: scsi 6:0:0:0: rejecting I/O to dead device
last message repeated 3 times
kernel: sda : READ CAPACITY failed.
kernel: sda : status=0, message=00, host=1, driver=00
kernel: sda : sense not available.
kernel: scsi 6:0:0:0: rejecting I/O to dead device
kernel: sda: Write Protect is off
kernel: sda: Mode Sense: 00 00 00 00
kernel: sda: assuming drive cache: write through
kernel: sda:<3>scsi 6:0:0:0: rejecting I/O to dead device
kernel: Buffer I/O error on device sda, logical block 0
kernel: scsi 6:0:0:0: rejecting I/O to dead device
kernel: Buffer I/O error on device sda, logical block 0
kernel: unable to read partition table
kernel: scsi 6:0:0:0: rejecting I/O to dead device
kernel: Buffer I/O error on device sda, logical block 31027
kernel: scsi 6:0:0:0: rejecting I/O to dead device
|
This log without
| Quote: | ohci_hcd 0000:00:02.0: wakeup
usb 2-2: new full speed USB device using ohci_hcd and address 9
usb 2-2: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
Vendor: HP Model: PhotoSmart M407 Rev: No.1
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 25089 512-byte hdwr sectors (13 MB)
sda: Write Protect is off
sda: Mode Sense: 87 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 25089 512-byte hdwr sectors (13 MB)
sda: Write Protect is off
sda: Mode Sense: 87 00 00 08
sda: assuming drive cache: write through
sda: unknown partition table
sd 7:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete |
With Ubuntu 5.04 all work |
|
| Back to top |
|
 |
manny15
Guru
Joined: 01 Dec 2002
Posts: 473
Location: USA
|
| Posted: Sun Feb 25, 2007 10:41 pm Post subject: |
|
|
I just started having problems mounting my HP M305 camera (with an SD card). Of course, it used to work just fine. Below is the dmesg of when the camera is plugged in.
| Code: |
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
Vendor: HP Model: PhotoSmart M305 Rev: No.1
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 248224 512-byte hdwr sectors (127 MB)
sda: Write Protect is off
sda: Mode Sense: 87 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 248224 512-byte hdwr sectors (127 MB)
sda: Write Protect is off
sda: Mode Sense: 87 00 00 08
sda: assuming drive cache: write through
sda: unknown partition table
sd 11:0:0:0: Attached scsi removable disk sda
sd 11:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
|
When trying to mount or access /dev/sda in any way (like using fdisk) the application hangs until I either unplug or power off the camera. Below is dmesg
| Code: |
hdd: cdrom_pc_intr: The drive appears confused (ireason = 0x01). Trying to recover by ending request.
usb 3-2: reset full speed USB device using uhci_hcd and address 13
hdd: cdrom_pc_intr: The drive appears confused (ireason = 0x01). Trying to recover by ending request.
hdd: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hdd: drive not ready for command
usb 3-2: reset full speed USB device using uhci_hcd and address 13
usb 3-2: reset full speed USB device using uhci_hcd and address 13
usb 3-2: reset full speed USB device using uhci_hcd and address 13
usb 3-2: reset full speed USB device using uhci_hcd and address 13
sd 11:0:0:0: SCSI error: return code = 0x00050000
end_request: I/O error, dev sda, sector 248216
Buffer I/O error on device sda, logical block 31027
hdd: cdrom_pc_intr: The drive appears confused (ireason = 0x01). Trying to recover by ending request.
hdd: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hdd: drive not ready for command
usb 3-2: reset full speed USB device using uhci_hcd and address 13
hdd: cdrom_pc_intr: The drive appears confused (ireason = 0x01). Trying to recover by ending request.
usb 3-2: reset full speed USB device using uhci_hcd and address 13
usb 3-2: reset full speed USB device using uhci_hcd and address 13
usb 3-2: reset full speed USB device using uhci_hcd and address 13
|
I don't see how hdd, my DVD drive, has anything to do with this. Oh, I use /dev/disk/by-id/usb-HP_PhotoSmart_M305, which typically points to /dev/sda, mount the camera. For some reason, it doesn't use a partition. I was able to mount the camera with Windows, so I suspect udev is a culprit. I guess it could be the kernel, but it hasn't been undated in some time. Also, I can mount other usb mass-storage devices with Gentoo.
Any ideas? |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
