| View previous topic :: View next topic |
| Author |
Message |
hrnick
Guru
Joined: 31 Aug 2002
Posts: 429
Location: Sweden
|
 Posted: Sat Dec 09, 2006 5:57 pm Post subject: Multicard reader stops working for a short while |
 |
|
I've got a multicard reader for the memory card on my digital camera that I use with hald, dbus and nautilus. It works fine to mount the card and copy files but after a while nautilus can no longer access the card for a short while and I get the following message in dmesg: | Code: | $ dmesg
usb 1-8: reset high speed USB device using ehci_hcd and address 10
usb 1-8: reset high speed USB device using ehci_hcd and address 10
usb 1-8: reset high speed USB device using ehci_hcd and address 10
usb 1-8: reset high speed USB device using ehci_hcd and address 10
usb 1-8: reset high speed USB device using ehci_hcd and address 10
usb 1-8: reset high speed USB device using ehci_hcd and address 10
usb 1-8: device firmware changed
usb 1-8: USB disconnect, address 10
sdd : READ CAPACITY failed.
sdd : status=0, message=00, host=7, driver=00
sdd : sense not available.
sde : READ CAPACITY failed.
sde : status=0, message=00, host=7, driver=00
sde : sense not available.
sdd: Write Protect is off
sdd: Mode Sense: 00 00 00 00
sdd: assuming drive cache: write through
sde: Write Protect is off
sde: Mode Sense: 00 00 00 00
sde: assuming drive cache: write through
sdd : READ CAPACITY failed.
sdd : status=0, message=00, host=7, driver=00
sdd : sense not available.
sde : READ CAPACITY failed.
sde : status=0, message=00, host=7, driver=00
sde : sense not available.
sdd: Write Protect is off
sdd: Mode Sense: 00 00 00 00
sdd: assuming drive cache: write through
sdd:<5>sde: Write Protect is off
sde: Mode Sense: 00 00 00 00
sde: assuming drive cache: write through
sde:<6>sd 10:0:0:2: SCSI error: return code = 0x70000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
sd 10:0:0:3: SCSI error: return code = 0x70000
end_request: I/O error, dev sde, sector 0
Buffer I/O error on device sde, logical block 0
sd 10:0:0:2: SCSI error: return code = 0x70000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
sd 10:0:0:3: SCSI error: return code = 0x70000
end_request: I/O error, dev sde, sector 0
Buffer I/O error on device sde, logical block 0
unable to read partition table
unable to read partition table
usb 1-8: new high speed USB device using ehci_hcd and address 11
usb 1-8: configuration #1 chosen from 1 choice
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
Vendor: Generic Model: USB SD Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 1984000 512-byte hdwr sectors (1016 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1984000 512-byte hdwr sectors (1016 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 11:0:0:0: Attached scsi removable disk sdb
sd 11:0:0:0: Attached scsi generic sg1 type 0
Vendor: Generic Model: USB CF Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
sd 11:0:0:1: Attached scsi removable disk sdc
sd 11:0:0:1: Attached scsi generic sg2 type 0
Vendor: Generic Model: USB SM Reader Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 00
sd 11:0:0:2: Attached scsi removable disk sdd
sd 11:0:0:2: Attached scsi generic sg3 type 0
Vendor: Generic Model: USB MS Reader Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 00
sd 11:0:0:3: Attached scsi removable disk sde
sd 11:0:0:3: Attached scsi generic sg4 type 0
usb-storage: device scan complete
usb 1-8: reset high speed USB device using ehci_hcd and address 11
usb 1-8: reset high speed USB device using ehci_hcd and address 11
usb 1-8: device firmware changed
usb 1-8: USB disconnect, address 11
sdc : READ CAPACITY failed.
sdc : status=0, message=00, host=7, driver=00
sdc : sense not available.
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sdc : READ CAPACITY failed.
sdc : status=0, message=00, host=7, driver=00
sdc : sense not available.
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sdc:<3>Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 0
unable to read partition table
sdc : READ CAPACITY failed.
sdc : status=0, message=00, host=7, driver=00
sdc : sense not available.
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sdc : READ CAPACITY failed.
sdc : status=0, message=00, host=7, driver=00
sdc : sense not available.
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sdc:<3> 11:0:0:1: rejecting I/O to dead device
Buffer I/O error on device sdc, logical block 0
11:0:0:1: rejecting I/O to dead device
Buffer I/O error on device sdc, logical block 0
unable to read partition table
11:0:0:1: rejecting I/O to dead device
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
11:0:0:1: rejecting I/O to dead device
Buffer I/O error on device sdc, logical block 0
11:0:0:1: rejecting I/O to dead device
Buffer I/O error on device sdc, logical block 0
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
11:0:0:1: rejecting I/O to dead device
usb 1-8: new high speed USB device using ehci_hcd and address 12
usb 1-8: configuration #1 chosen from 1 choice
scsi12 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
Vendor: Generic Model: USB SD Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 1984000 512-byte hdwr sectors (1016 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1984000 512-byte hdwr sectors (1016 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 12:0:0:0: Attached scsi removable disk sdb
sd 12:0:0:0: Attached scsi generic sg1 type 0
Vendor: Generic Model: USB CF Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 00
sd 12:0:0:1: Attached scsi removable disk sdc
sd 12:0:0:1: Attached scsi generic sg2 type 0
Vendor: Generic Model: USB SM Reader Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 00
sd 12:0:0:2: Attached scsi removable disk sdd
sd 12:0:0:2: Attached scsi generic sg3 type 0
Vendor: Generic Model: USB MS Reader Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 00
sd 12:0:0:3: Attached scsi removable disk sde
sd 12:0:0:3: Attached scsi generic sg4 type 0
usb-storage: device scan complete
usb 1-8: reset high speed USB device using ehci_hcd and address 12
usb 1-8: reset high speed USB device using ehci_hcd and address 12
usb 1-8: reset high speed USB device using ehci_hcd and address 12
usb 1-8: reset high speed USB device using ehci_hcd and address 12 |
Any ideas what the problem might be? |
|
| Back to top |
|
 |
hrnick
Guru
Joined: 31 Aug 2002
Posts: 429
Location: Sweden
|
| Posted: Wed Dec 13, 2006 9:23 am Post subject: |
|
|
| Solved, it was hardware error, had the same problems in windows... |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
