| View previous topic :: View next topic |
| Author |
Message |
knue
Tux's lil' helper
Joined: 13 Oct 2004
Posts: 139
|
 Posted: Wed Dec 13, 2006 2:00 am Post subject: harddisk broken? |
 |
|
Hi,
I had recently some random crashes. They happen quit seldom, but they are there. I think it is my harddisk's fault. It usually happens when I want to save a file. Then the LED of the harddisk does not blink anymore and everthing crashes a few secons later. When I press "reset" I get some disk failure errors and cannot boot my computer again. Only if I do a complete power off and switch it on again everything works fine again.
Here my dmesg output after a reboot of my last crash:
| Code: | Bootdata ok (command line is root=/dev/sda4)
Linux version 2.6.18-gentoo-r3 (root@gentoo64) (gcc version 4.1.1 (Gentoo 4.1.1-r1)) #2 SMP Sat Dec 2 21:09:20 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7580
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff30c0
ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000003fff9180
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff92c0
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff90c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003fff0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003fff0000
On node 0 totalpages: 256739
DMA zone: 2234 pages, LIFO batch:0
DMA32 zone: 254505 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
Built 1 zonelists. Total pages: 256739
Kernel command line: root=/dev/sda4
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2211.335 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ 100000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1025008k/1048512k available (3997k kernel code, 23116k reserved, 1767k data, 236k init)
Calibrating delay using timer specific routine.. 4425.36 BogoMIPS (lpj=8850730)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12564404
Detected 12.564 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... OK.
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
PCI: No mmconfig possible on device 0:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
Boot video device is 0000:05:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 3 of device 0000:05:00.0
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:09.0
IO window: d000-dfff
MEM window: fe900000-fe9fffff
PREFETCH window: fea00000-feafffff
PCI: Bridge: 0000:00:0b.0
IO window: c000-cfff
MEM window: fe800000-fe8fffff
PREFETCH window: fe700000-fe7fffff
PCI: Bridge: 0000:00:0c.0
IO window: b000-bfff
MEM window: fe600000-fe6fffff
PREFETCH window: fe500000-fe5fffff
PCI: Bridge: 0000:00:0d.0
IO window: a000-afff
MEM window: fe400000-fe4fffff
PREFETCH window: fe300000-fe3fffff
PCI: Bridge: 0000:00:0e.0
IO window: 9000-9fff
MEM window: fc000000-fdffffff
PREFETCH window: b0000000-cfffffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/W].
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
Real Time Clock Driver v1.12ac
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [THRM] (40 C)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
GSI 16 sharing vector 0xD9 and IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
input: AT Translated Set 2 keyboard as /class/input/input0
eth0: forcedeth.c: subsystem: 01565:2501 bound to 0000:00:0a.0
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 162
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hdb: DVD-ROM BDV316C, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 1X DVD-ROM drive, 512kB Cache, UDMA(33)
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006)
megasas: 00.00.03.01 Sun May 14 22:49:52 PDT 2006
libata version 2.00 loaded.
sata_nv 0000:00:07.0: version 2.0
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
GSI 17 sharing vector 0xE1 and IRQ 17
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF600 irq 225
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF608 irq 225
scsi0 : sata_nv
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 300)
Vendor: ATA Model: Maxtor 6V250F0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
GSI 18 sharing vector 0xE9 and IRQ 18
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF100 irq 233
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF108 irq 233
scsi2 : sata_nv
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_nv
ata4: SATA link down (SStatus 0 SControl 300)
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.01
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
GSI 19 sharing vector 0x32 and IRQ 19
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 50, io mem 0xfebfe000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 217, io mem 0xfebff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
USB Universal Host Controller Interface driver v3.0
usb 2-5: new low speed USB device using ohci_hcd and address 2
usb 2-5: configuration #1 chosen from 1 choice
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-5
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
oprofile: using NMI interrupt.
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 280 bytes per conntrack
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x6
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x8
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
ACPI: (supports S0 S1 S4 S5)
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: sda4: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 6964058
ext3_orphan_cleanup: deleting unreferenced inode 6964057
ext3_orphan_cleanup: deleting unreferenced inode 6964050
ext3_orphan_cleanup: deleting unreferenced inode 6964056
ext3_orphan_cleanup: deleting unreferenced inode 6964042
ext3_orphan_cleanup: deleting unreferenced inode 6964038
ext3_orphan_cleanup: deleting unreferenced inode 6964037
ext3_orphan_cleanup: deleting unreferenced inode 6964014
ext3_orphan_cleanup: deleting unreferenced inode 6963982
ext3_orphan_cleanup: deleting unreferenced inode 6964012
ext3_orphan_cleanup: deleting unreferenced inode 6964008
ext3_orphan_cleanup: deleting unreferenced inode 6964025
ext3_orphan_cleanup: deleting unreferenced inode 6964009
ext3_orphan_cleanup: deleting unreferenced inode 6964019
ext3_orphan_cleanup: deleting unreferenced inode 6964035
ext3_orphan_cleanup: deleting unreferenced inode 6964049
ext3_orphan_cleanup: deleting unreferenced inode 6964020
ext3_orphan_cleanup: deleting unreferenced inode 6964032
ext3_orphan_cleanup: deleting unreferenced inode 6964010
ext3_orphan_cleanup: deleting unreferenced inode 6964013
ext3_orphan_cleanup: deleting unreferenced inode 6964001
ext3_orphan_cleanup: deleting unreferenced inode 6964000
ext3_orphan_cleanup: deleting unreferenced inode 6963999
ext3_orphan_cleanup: deleting unreferenced inode 6963996
ext3_orphan_cleanup: deleting unreferenced inode 6963991
EXT3-fs: sda4: 25 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 236k freed
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:04.0 to 64
intel8x0_measure_ac97_clock: measured 58599 usecs
intel8x0: clocking to 47009
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
GSI 20 sharing vector 0x3A and IRQ 20
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:05:00.0 to 64
NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-9631 Thu Nov 9 17:35:27 PST 2006
EXT3 FS on sda4, internal journal
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
Adding 506036k swap on /dev/sda2. Priority:-1 extents:1 across:506036k
eth0: no IPv6 routers present |
Is there something to be sure that my harddisk is broken? I still have warranty on that thing. If I go to the store and say "hey, my linux box crashes sometimes after 12 hours of work" I don't think they will give me a new one.
Perhaps this is not a hardware problem. Here some other information:
| Code: | # uname -a
Linux gentoo64 2.6.18-gentoo-r3 #2 SMP Sat Dec 2 21:09:20 UTC 2006 x86_64 AMD Athlon(tm) 64 Processor 3500+ AuthenticAMD GNU/Linux
# lsmod
Module Size Used by
snd_seq 56544 0
snd_pcm_oss 45664 0
snd_mixer_oss 18432 1 snd_pcm_oss
nvidia 5651288 22
snd_intel8x0 34536 1
snd_ac97_codec 105624 1 snd_intel8x0
snd_ac97_bus 4736 1 snd_ac97_codec
snd_pcm 81544 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 23368 2 snd_seq,snd_pcm
snd 55976 9 snd_seq,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc 10320 2 snd_intel8x0,snd_pcm
# emerge --info
Portage 2.1.2_rc3-r1 (default-linux/amd64/2006.0, gcc-4.1.1, glibc-2.5-r0, 2.6.18-gentoo-r3 x86_64)
=================================================================
System uname: 2.6.18-gentoo-r3 x86_64 AMD Athlon(tm) 64 Processor 3500+
Gentoo Base System version 1.12.6
Last Sync: Sun, 10 Dec 2006 20:00:07 +0000
dev-java/java-config: 1.3.7, 2.0.30
dev-lang/python: 2.4.4
dev-python/pycrypto: 2.0.1-r5
sys-apps/sandbox: 1.2.18.1
sys-devel/autoconf: 2.13, 2.61
sys-devel/automake: 1.4_p6, 1.5, 1.6.3, 1.7.9-r1, 1.8.5-r3, 1.9.6-r2, 1.10
sys-devel/binutils: 2.17
sys-devel/gcc-config: 1.3.14
sys-devel/libtool: 1.5.22
virtual/os-headers: 2.6.17-r2
ACCEPT_KEYWORDS="amd64 ~amd64"
AUTOCLEAN="yes"
CBUILD="x86_64-pc-linux-gnu"
CFLAGS="-march=k8 -pipe -O2 -fomit-frame-pointer"
CHOST="x86_64-pc-linux-gnu"
CONFIG_PROTECT="/etc /usr/kde/3.5/env /usr/kde/3.5/share/config /usr/kde/3.5/shutdown /usr/share/X11/xkb /usr/share/config"
CONFIG_PROTECT_MASK="/etc/env.d /etc/env.d/java/ /etc/gconf /etc/java-config/vms/ /etc/revdep-rebuild /etc/terminfo /etc/texmf/web2c"
CXXFLAGS="-march=k8 -pipe -O2 -fomit-frame-pointer"
DISTDIR="/usr/portage/distfiles"
FEATURES="autoconfig distlocks metadata-transfer sandbox sfperms strict"
GENTOO_MIRRORS="http://linux.rz.ruhr-uni-bochum.de/download/gentoo-mirror/ "
LANG="en_US"
LC_ALL="en_US"
LINGUAS="de en"
MAKEOPTS="-j2"
PKGDIR="/usr/portage/packages"
PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times --compress --force --whole-file --delete --delete-after --stats --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages"
PORTAGE_TMPDIR="/var/tmp"
PORTDIR="/usr/portage"
PORTDIR_OVERLAY="/usr/local/portage"
SYNC="rsync://rsync.gentoo.org/gentoo-portage"
USE="amd64 16bit X aac aalib acpi aiglx alsa amarok amuled aoss apache2 arts artswrappersuid asf audiofile bash-completion berkdb bidi bitmap-fonts cairo cdda cddb cdinstall cdparanoia cdrom cjk cli codecs corba cracklib crypt css cups dba dbus dga dhcp dlloader dmi dri dts dv dvb dvd dvdr dvdread edl eds elibc_glibc emboss encode esd fbcon ffmpeg flac foomaticdb freetts gcj gd-external ggi gif gimp glitz gnutls gphoto2 gpm gsm gstreamer gtk gtk2 hal iconv imagemagick imlib input_devices_keyboard input_devices_mouse ipv6 isdnlog jack java jpeg kde kdeenablefinal kdehiddenvisibility kernel_linux kqemu libcaca linguas_de linguas_en live logitech-mouse lzo lzw lzw-tiff mad mikmod mp3 mpeg mpeg4 mplayer multiuser musepack musicbrainz mysql mythtv ncurses nls no-seamonkey no_wxgtk1 nptl nptlonly nsplugin nvidia ogg openal opengl pam pcre pdf perl png ppds pppd print python qt3 qt4 quicktime rdesktop readline reflection reiserfs remote rtc samba sdk sdl session skins sndfile speex spell spl ssl stats stream subversion svg tcpd tetex tga theora tiff truetype truetype-fonts type1 type1-fonts unicode upnp usb userland_GNU v4l v4l2 vcd video_cards_fbdev video_cards_nv video_cards_nvidia video_cards_vesa visualization vlm vorbis wifi wxwindows xanim xcomposite xine xinerama xml xorg xpm xscreensaver xv xvmc zeroconf zlib"
Unset: CTARGET, EMERGE_DEFAULT_OPTS, INSTALL_MASK, LDFLAGS, PORTAGE_RSYNC_EXTRA_OPTS |
|
|
| Back to top |
|
 |
Section_8
l33t
Joined: 22 May 2004
Posts: 627
|
| Posted: Wed Dec 13, 2006 3:47 am Post subject: |
|
|
| Have you emerged smartmontools? |
|
| Back to top |
|
|
knue
Tux's lil' helper
Joined: 13 Oct 2004
Posts: 139
|
| Posted: Wed Dec 13, 2006 5:46 pm Post subject: |
|
|
| Section_8 wrote: | | Have you emerged smartmontools? |
Thx. I will try this out. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
