| View previous topic :: View next topic |
| Author |
Message |
jrtayloriv
Tux's lil' helper
Joined: 31 Dec 2004
Posts: 149
Location: N. Idaho
|
 Posted: Mon Jan 01, 2007 8:16 pm Post subject: Intel 830M Motherboard Hardware Sensors |
 |
|
I am trying to configure cpufreqd, acpi, and lm_sensors for my Compaq Evo N600C laptop. I have an Intel 830M motherboard and am running Gentoo Linux with a 2.6.18 kernel built from the Suspend2 sources. I need to know what hardware sensors modules to enable in the kernel configuration for this motherboard.
Here is the output from lspci -vv:
| Code: |
0:00.0 Host bridge: Intel Corporation 82830 830 Chipset Host Bridge (rev 02)
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at 60000000 (32-bit, prefetchable) [size=256M]
Capabilities: [40] Vendor Specific Information
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
00:01.0 PCI bridge: Intel Corporation 82830 830 Chipset AGP Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 40200000-402fffff
Prefetchable memory behind bridge: 48000000-4fffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1) (rev 01) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 4000 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #2) (rev 01) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 4020 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #3) (rev 01) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 4040 [size=32]
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 41) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=07, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 40000000-401fffff
Prefetchable memory behind bridge: 20000000-23ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 4060 [size=16]
Region 5: Memory at 24000000 (32-bit, non-prefetchable) [size=1K]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 48000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at 40200000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 40220000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:03.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=03, sec-latency=176
Memory window 0: 20000000-21fff000 (prefetchable)
Memory window 1: 26000000-27fff000
I/O window 0: 00002c00-00002cff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
02:03.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40080000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 22000000-23fff000 (prefetchable)
Memory window 1: 28000000-29fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
02:04.0 Communication controller: Agere Systems LT WinModem (rev 02)
Subsystem: AMBIT Microsystem Corp. Evo N600c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40180000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 2840 [size=8]
Region 2: I/O ports at 2000 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VM (KM) Ethernet Controller (rev 41)
Subsystem: Compaq Computer Corporation Evo N600c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2800 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:09.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12)
Subsystem: Compaq Computer Corporation Unknown device 0094
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:00.0 Network controller: RaLink RT2561/RT61 802.11g PCI
Subsystem: RaLink Unknown device 2561
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 26000000 (32-bit, non-prefetchable) [size=32K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
Any help would be greatly appreciated.
Thanks,
jrtayloriv |
|
| Back to top |
|
 |
jrtayloriv
Tux's lil' helper
Joined: 31 Dec 2004
Posts: 149
Location: N. Idaho
|
| Posted: Thu Jan 04, 2007 5:24 am Post subject: |
|
|
And I've got a Pentium III Mobile 1066Mhz processor, if that makes any difference:
Here is /proc/cpuinfo:
| Code: |
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 11
model name : Intel(R) Pentium(R) III Mobile CPU 1066MHz
stepping : 1
cpu MHz : 731.500
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1462.37
|
Thanks,
jrtayloriv |
|
| Back to top |
|
|
jrtayloriv
Tux's lil' helper
Joined: 31 Dec 2004
Posts: 149
Location: N. Idaho
|
| Posted: Fri Jan 05, 2007 3:30 am Post subject: |
|
|
And happy new year and all that. Anybody want to answer this?
jrtayloriv |
|
| Back to top |
|
|
vfronda
n00b
Joined: 07 Sep 2006
Posts: 21
|
| Posted: Fri Jan 05, 2007 3:41 am Post subject: Seasons greetings from the folks at Drake software |
|
|
| I couldnt tell you the answer to your questoni but it looks as though you are missing something in your life. Have you thought of accepting jesus into your soul. Recent polls suggest that jesus has significantly improved the lives of some people. What a bargain!!! |
|
| Back to top |
|
|
jrtayloriv
Tux's lil' helper
Joined: 31 Dec 2004
Posts: 149
Location: N. Idaho
|
| Posted: Fri Jan 05, 2007 3:46 am Post subject: |
|
|
| I don't need lm_sensors anymore, now that Jesus is in my life. Thank you vfronda! And Jesus. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
