| View previous topic :: View next topic |
| Author |
Message |
crimson
Guru
Joined: 27 Apr 2002
Posts: 430
Location: Cedar Rapids, IA
|
 Posted: Fri May 09, 2003 7:52 pm Post subject: pci radeon problems |
 |
|
Hi, I have a pci radeon card, it's an older model.. nothing good. I'm having some problems with X. X does start, but heres the error I get:
Using vt7
(WW RADEON: No matching Device section for instance (BusID PCI:1:0:0) found
Symbol drmGetClient from module /usr/X11R6/modules/drivers/radeon_drv.o is unresolved
lsmod shows radeon in the list.
Also, I'm not using xscreensaver, but when I'm in X and I'm idle for a while instead of the screen turning black, it tries to turn black and "gets stuck in between". It just keeps tryin to switch modes, and this kinda scares me, I don't want to mess up this monitor. I hope someone can help  . |
|
| Back to top |
|
 |
Supermule
Guru
Joined: 05 Mar 2003
Posts: 510
Location: /denmark/fyn
|
| Posted: Fri May 09, 2003 8:41 pm Post subject: |
|
|
Could u copy the relevant sections of your XF86config? Or the whole file for that matter
_________________
regards,
Supermule |
|
| Back to top |
|
|
crimson
Guru
Joined: 27 Apr 2002
Posts: 430
Location: Cedar Rapids, IA
|
| Posted: Fri May 09, 2003 11:47 pm Post subject: |
|
|
gladly . I hope I can get this resolved, because I'm really worried my monitor will go bad. The HorizSync values for my monitor are what I found on all the websites:
H Frequency: 31.5/35-40/46-51 Khz
V Frequency: 50-90 Hz
| Code: |
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "speedo"
# Load "freetype"
# Load "xtt"
# This loads the GLX module
# Load "glx"
# This loads the DRI module
# Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/TTF"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
# FontPath "/usr/X11R6/lib/X11/fonts/TrueType/"
# FontPath "/usr/X11R6/lib/X11/fonts/freefont/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
# The module search path. The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Option "Dont Zoom"
# Option "DisableVidModeExtension"
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
# Option "Protocol" "Xqueue"
Option "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
Option "XkbRules" "xfree86"
Option "XkbModel" "hp2505"
Option "XkbLayout" "us"
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "PS/2"
Option "Device" "/dev/mouse"
# Mouse-speed setting for PS/2 mouse.
Option "Resolution" "1200"
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "Mon"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5, 35-40, 46-51
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-90
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "radeon"
Driver "radeon"
#VideoRam 32768
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "radeon"
Monitor "Mon"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
# Section "DRI"
# Mode 0666
# EndSection
|
there she is |
|
| Back to top |
|
|
JohnY
Guru
Joined: 26 Jul 2002
Posts: 305
|
| Posted: Sat May 10, 2003 3:20 pm Post subject: |
|
|
crimson - here is a working radeon-le XF86Config with most of the comments stripped out
| Code: |
Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules"
# FontPath "unix/:-1"
FontPath "/usr/X11R6/lib/X11/fonts/truetype"
FontPath "/usr/X11R6/lib/X11/fonts/TTF"
FontPath "/usr/X11R6/lib/X11/fonts/sharefont"
FontPath "/usr/X11R6/lib/X11/fonts/freefont"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/CID/"
EndSection
# Module loading section
Section "Module"
Load "ddc"
Load "GLcore"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
# Load "pex5"
Load "record"
# Load "xie"
Load "bitmap"
Load "freetype"
Load "speedo"
Load "type1"
Load "vbe"
Load "int10"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
# Modified by mouseconfig
Driver "mouse"
Option "Device" "/dev/mouse"
Option "Protocol" "IMPS/2"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
Identifier "SAM4F26"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 30 - 96
VertRefresh 50 - 160
Gamma 1.2
Option "DPMS" "on"
EndSection
Section "Device"
Identifier "radeonle"
Driver "radeon"
# Option "pci_retry"
# Option "FastVram"
Option "AGPMode" "2"
Option "DPMS" "on"
BoardName "Unknown"
EndSection
Section "Device"
Identifier "Linux Frame Buffer"
Driver "fbdev"
BoardName "Unknown"
EndSection
Section "Screen"
Identifier "Screen0"
Device "radeonle"
Monitor "SAM4F26"
DefaultDepth 16
Subsection "Display"
Depth 16
Modes "1024x768"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
|
This one works with dri at a default depth of 16.
The config you posted has glx and dri commented out (could be the source of your unresolved symbols) or maybe you could temporarly comment out these lines:
| Code: |
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
|
to see if your unrsolved symbols have anything to to with the omitted DGA. They sound like dri related syms to me.
JohnY |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Desktop Environments
