FmRadio Flyvideo300

[bhashu24]

Ich habe schwierigkeiten mit dem FmRadioempfang meiner Flyvideo300.
Fernsehempfang(Kabel) klappt einwandfrei. Nur Radiosender kann ich nicht scannen. Alle Programme (fmscan,radio,k/g/gnome-radio..) laufen unser Frequenzband (87-108MHZ) sauber durch aber es folgt nur rauschen. Wer kann mir sagen wie man den Radioteil einschaltet??


lspci -vv
01:0a.0 Multimedia controller: Philips Semiconductors SAA7134 Video Broadcast Decoder (rev 01)
Subsystem: Unknown device 4e42:0138
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at df001000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=3 PME-

dmesg | grep saa

saa7130/34: v4l2 driver version 0.2.14 loaded
saa7134[0]: found at 0000:01:0a.0, rev: 1, irq: 20, latency: 32, mmio: 0xdf001000
saa7134[0]: subsystem: 4e42:0138, board: LifeView FlyVIDEO3000 [card=2,insmod option]
saa7134[0]: board init: gpio is 39100
saa7134[0]: there are different flyvideo cards with different tuners
saa7134[0]: out there, you might have to use the tuner=<nr> insmod
saa7134[0]: option to override the default value.
input: saa7134 IR (LifeView FlyVIDEO30 as /class/input/input8
saa7134[0]: i2c eeprom 00: 42 4e 38 01 10 28 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 0-0061: chip found @ 0xc2 (saa7134[0])
tuner 0-0061: saa7134[0] tuner I2C addr 0xc2 with type 51 used for 0x0e
tuner 0-0061: saa7134[0] tuner I2C addr 0xc2 with type 51 used for 0x0e
tuner 0-0063: chip found @ 0xc6 (saa7134[0])
saa7134[0]: registered device video1 [v4l2]
saa7134[0]: registered device vbi1
saa7134[0]: registered device radio1

v4l-info /dev/radio1
general info
VIDIOC_QUERYCAP
driver : "saa7134"
card : "LifeView FlyVIDEO3000"
bus_info : "PCI:0000:01:0a.0"
version : 0.2.14
capabilities : 0x10000 [TUNER]

standards

inputs
VIDIOC_ENUMINPUT(0)
index : 0
name : "Radio"
type : TUNER
audioset : 0
tuner : 0
std : 0x0 []
status : 0x0 []

tuners
VIDIOC_G_TUNER(0)
index : 0
name : "Radio"
type : RADIO
capability : 0x11 [LOW,STEREO]
rangelow : 1040000
rangehigh : 1728000
rxsubchans : 0x1 [MONO]
audmode : STEREO
signal : 16384
afc : 0

controls
VIDIOC_QUERYCTRL(BASE+9)
id : 9963785
type : BOOLEAN
name : "Mute"
minimum : 0
maximum : 1
step : 0
default_value : 0
flags : 0

### video4linux device info [/dev/radio1] ###
general info
VIDIOCGCAP
name : "LifeView FlyVIDEO3000"
type : 0x2 [TUNER]
channels : 1
audios : 0
maxwidth : 0
maxheight : 0
minwidth : 48
minheight : 32

channels
VIDIOCGCHAN(0)
channel : 0
name : "Radio"
tuners : 1
flags : 0x1 [TUNER]
type : TV
norm : 0

tuner
VIDIOCGTUNER
tuner : 0
name : "Radio"
rangelow : 1040000
rangehigh : 1728000
flags : 0x8 [LOW]
mode : AUTO
signal : 16384

audio
VIDIOCGAUDIO
audio : 0
volume : 0
bass : 0
treble : 0

[ghp]

Hallo bhashu24,

hast du inzwisschen erfolg gehat mit dem Radioempfang?


Danke,

Gerard