| View previous topic :: View next topic |
| Author |
Message |
thinker5555
Tux's lil' helper
Joined: 03 Jun 2002
Posts: 77
Location: Texas
|
 Posted: Sat Jun 22, 2002 8:44 pm Post subject: PCI ATA card gone with gentoo-sources (2.4.19-r7) |
 |
|
I just installed Gentoo on /dev/hde5 with the XFS file system, /boot on /dev/hda1 with ext2, and built my kernel using the 2.4.19-r7 gentoo-sources. After finalizing the installation and rebooting, I get this error during bootup:
| Code: |
VFS: Cannot open root device "hde5" on 21:05
Please append a correct "root=" boot option
Kernel Panic: VFS: Unable to mount root fs on 21:05
|
At first I thought something was wrong with my grub config. I checked that, and it was fine. Then I thought I had forgotten something for my hardware in my kernel. I checked, and my PCI, ATA, and filesystem stuff was compiled in and fine. I then realized that my PCI ATA card was not being found.
I have a second (well, my first, technically) install of Gentoo on hde6, but it's using the 2.4.18 kernel, and it's using the exact same settings (as far as PCI, ATA, and my file system) and it finds the card, and therefore boots, correctly.
Short of going back to the 2.4.18 sources, does anyone have any suggestions or ideas?
Thanks,
Jeremy |
|
| Back to top |
|
 |
pjp
Administrator
Joined: 16 Apr 2002
Posts: 20485
|
| Posted: Sat Jun 22, 2002 9:26 pm Post subject: |
|
|
Try 'make mrproper'
This thread has someone mention using this. This one is a discussion about mrproper.
EDIT: Please post your results if you try it.
_________________
Quis separabit? Quo animo? |
|
| Back to top |
|
|
thinker5555
Tux's lil' helper
Joined: 03 Jun 2002
Posts: 77
Location: Texas
|
| Posted: Sat Jun 22, 2002 10:09 pm Post subject: |
|
|
Thanks for the links. The first one sounds like my problem, but their suggestion didn't work. By results, I'm not sure if you mean specific output of mrproper or not. I had forgotten to mention that I had given the make mrproper a try, but I still had no luck.  I didn't save any output, though. It 'succeeded', and I didn't think to do so. The only error I get is on bootup when finding my PCI card fails, and it only fails because I'm trying to boot from it.
Eh, and I just thought of this... I'm running the 1.3b stage 1 beta.(GCC3.x) Would this have anything to do with it?
Thanks for the idea, though.
Jeremy |
|
| Back to top |
|
|
pjp
Administrator
Joined: 16 Apr 2002
Posts: 20485
|
| Posted: Sun Jun 23, 2002 6:05 am Post subject: |
|
|
No idea about GCC3.x. Many of the rx kernels seem to have problems with Promise controllers.
This is why I have yet to touch my working kernel, though I'd like to add preemptive support.
I was hoping the mrproper was the solution. That yours failed was what I wanted to know,
though I was hoping it would have worked.
_________________
Quis separabit? Quo animo? |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
