| View previous topic :: View next topic |
| Author |
Message |
edoiks2
n00b
Joined: 19 Nov 2007
Posts: 6
|
 Posted: Mon Nov 19, 2007 8:14 pm Post subject: Alsa + Intel HDA z Benq R55E |
 |
|
Witajcie,
problem jest taki, audio dziala, tylko że zachowuje się tak jak nie powinno, tj. mam trzy gniazdka, słuchawki, line-in i mic, niestety tylko wejście słuchawkowe działa jak należy, line-in działa jak drugie wyjście słuchawkowe, tylko że głośniczki systemowe się nie wyłączają, a mikrofonu nie uświadcze, działają tylko te wbudowane w lapka, ale są marnej jakości i uniemożliwiają rozmowę choćby przez skype.
a teraz co mi wyrzuca lspci:
| Code: | | 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) |
dalej lspci -vv:
| Code: |
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: QUANTA Computer Inc Softmodem
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at dc440000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel
Capabilities: [130] Root Complex Link
|
mam alsa-driver-1.0.15, ale ze sterownikami z jajka działało podobnie, nie wiem co już mam zrobić chciałbym żeby wszystko działało, ale chyba zawiodłem, i nie wiem w czym rzecz. Chip niby wykryty dobrze, a jednak nie działają te kanały co powinny,
w /proc/asound/card0/codec* w pierwszej linijce jest:
| Code: | | Codec: Conexant CX20549 (Venice) |
więc teoretycznie moja karta
jeszcze dodam że jajko mam 2.6.22-gentoo-r8_02
oczywiście w jajku jest obsługa alsy, ale brak driverów z jajka tylko z paczki.
bawiłem się modelami jako argumenty modulu snd-hda-intel ale mam wrazenie ze to nie dziala.
proszę o pomoc.
jeszcze dmesg:
| Code: |
Linux version 2.6.22-gentoo-r8_02 (root@edoiks) (gcc version 4.2.1 (Gentoo 4.2.1 p1.0)) #5 SMP Tue Oct 23 21:30:59 CEST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f690000 (usable)
BIOS-e820: 000000003f690000 - 000000003f699000 (ACPI data)
BIOS-e820: 000000003f699000 - 000000003f700000 (ACPI NVS)
BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
118MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7700
Entering add_active_range(0, 0, 259728) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 259728
early_node_map[1] active PFN ranges
0: 0 -> 259728
On node 0 totalpages: 259728
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 237 pages used for memmap
HighMem zone: 30115 pages, LIFO batch:7
DMI present.
ACPI: RSDP 000F75D0, 0014 (r0 PTLTD )
ACPI: RSDT 3F692E3E, 0040 (r1 GATEWA M 20061011 LTP 0)
ACPI: FACP 3F698E2E, 0074 (r1 GATEWA M 20061011 LOHR 5A)
ACPI: DSDT 3F693552, 58DC (r1 GATEWA M 20061011 MSFT 100000E)
ACPI: FACS 3F699FC0, 0040
ACPI: APIC 3F698EA2, 0068 (r1 GATEWA M 20061011 LOHR 5A)
ACPI: BOOT 3F698FD8, 0028 (r1 GATEWA M 20061011 LTP 1)
ACPI: MCFG 3F698F42, 003C (r1 GATEWA M 20061011 LOHR 5A)
ACPI: APIC 3F698F7E, 005A (r1 GATEWA M 20061011 LTP 0)
ACPI: SSDT 3F69337E, 01D0 (r1 PmRef Cpu0Cst 3001 INTL 20050228)
ACPI: SSDT 3F692E7E, 0500 (r1 PmRef CpuPm 3000 INTL 20050228)
ACPI: BIOS bug: multiple APIC/MADT found, using 0
ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Built 1 zonelists. Total pages: 257699
Kernel command line: auto BOOT_IMAGE=gentoo_2 ro root=100 initrc=/linuxrc ramdisk=8192 splash=silent,fadein,theme:livecd-2007.0 CONSOLE=/dev/tty1 real_root=/dev/sda1 udev
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0571000 soft=c0551000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1729.721 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1021684k/1038912k available (3249k kernel code, 16588k reserved, 848k data, 276k init, 121408k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0507000 - 0xc054c000 ( 276 kB)
.data : 0xc042c79c - 0xc0500a3c ( 848 kB)
.text : 0xc0100000 - 0xc042c79c (3249 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3462.17 BogoMIPS (lpj=17310880)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 0000c109 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00002940 0000c109 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Celeron(R) M CPU 430 @ 1.73GHz stepping 08
Total of 1 processors activated (3462.17 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: Please test with "acpi_osi=!Linux"
Please send dmidecode to linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 8 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:1c.0
IO window: 2000-2fff
MEM window: d8000000-d9ffffff
PREFETCH window: d2000000-d3ffffff
PCI: Bridge: 0000:00:1c.1
IO window: 3000-3fff
MEM window: d6000000-d7ffffff
PREFETCH window: d0000000-d1ffffff
PCI: Bridge: 0000:00:1c.2
IO window: 4000-4fff
MEM window: da000000-dbffffff
PREFETCH window: d4000000-d5ffffff
PCI: Bus 6, cardbus bridge: 0000:05:01.0
IO window: 00005000-000050ff
IO window: 00005400-000054ff
PREFETCH window: 50000000-53ffffff
MEM window: 54000000-57ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 5000-5fff
MEM window: dc000000-dc0fffff
PREFETCH window: 50000000-53ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:05:01.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:05:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2337k freed
Simple Boot Flag value 0x82 read from CMOS RAM was invalid
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1195474603.340:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
GFS2 (built Oct 23 2007 21:26:20) installed
Lock_Nolock (built Oct 22 2007 23:51:58) installed
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
intel_rng: FWH not detected
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
vesafb: framebuffer at 0xc0000000, mapped to 0xf8a00000, using 3072k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to NOHz mode on CPU #0
isapnp: No Plug & Play device found
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
intelfb: Cannot reserve FB region.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000118b0 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000118b8 irq 15
ata1.00: ATA-7: HTS541060G9SA00, MB3OC60R, max UDMA/100
ata1.00: 117210240 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2.00: ATAPI: PHILIPS DVD+/-RW SDVD8820, AX02, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA HTS541060G9SA00 MB3O PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 > sda3
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM PHILIPS DVD+-RW SDVD8820 AX02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2Q] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 276k freed
ata1: soft resetting port
ata1.00: configured for UDMA/100
ata1: EH complete
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdc444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Initializing USB Mass Storage driver...
Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 17, io base 0x00001880
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: A4Tech USB Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [A4Tech USB Optical Mouse] on usb-0000:00:1d.2-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
PCI: Enabling device 0000:05:01.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:01.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:05:01.1 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[dc005000-dc0057ff] Max Packet=[2048] IR/IT contexts=[4/8]
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
JFS: nTxBlock = 8004, nTxLock = 64035
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3.3)
ath_pci: no version for "ieee80211_encap" found: kernel tainted.
ath_pci: 0.9.4.5 (0.9.3.3)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:04:00.0 to 64
sky2 0000:04:00.0: v1.14 addr 0xda000000 irq 18 Yukon-EC Ultra (0xb4) rev 2
sky2 eth0: addr 00:16:36:b3:26:80
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
ath_pci: switching rfkill capability on
ath_rate_sample: 1.2 (0.9.3.3)
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 10.0 phy 6.1 radio 10.2
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5424/2424: mem=0xd8000000, irq=17
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Enabling device 0000:05:01.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:01.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:05:01.2 to 64
Yenta: CardBus bridge found at 0000:05:01.0 [152d:0753]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:05:01.0, mfunc 0x01001922, devctl 0x66
Real Time Clock Driver v1.12ac
Yenta: ISA IRQ mask 0x0cf8, PCI irq 18
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#05) from #05 to #07
pcmcia: parent PCI bridge I/O window: 0x5000 - 0x5fff
cs: IO port probe 0x5000-0x5fff: clean.
pcmcia: parent PCI bridge Memory window: 0xdc000000 - 0xdc0fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
apm: BIOS not found.
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: AC Adapter [ACAD] (on-line)
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input6
ACPI: Lid Switch [LID]
ACPI: Error installing notify handler
Device 'dock.0' does not have a release() function, it is broken and must be fixed.
WARNING: at drivers/base/core.c:107 device_release()
[<c03031fd>] [<c0303214>] [<c0303db4>] [<c0369f2d>] [<f9302782>] [<c034b6bb>] [<c0349f94>] [<f9302599>] [<f898a03c>] [<f9302599>] [<c013dbb5>] [<c0366925>] [<c0103d2a>] [<c0420000>] =======================
No dock devices found.
ACPI: Thermal Zone [TZ00] (49 C)
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
wbsd: Winbond W83L51xD SD/MMC card interface driver
wbsd: Copyright(c) Pierre Ossman
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:05:01.3 [104c:803c] (rev 0)
PCI: Enabling device 0000:05:01.3 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:01.3[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:05:01.3 to 64
mmc0: SDHCI at 0xdc005800 irq 18 DMA
Adding 1108476k swap on /dev/sda3. Priority:-1 extents:1 across:1108476k
Clocksource tsc unstable (delta = -303071698 ns)
sky2 eth0: enabling interface
sky2 eth0: ram buffer 0K
fbsplash: console 0 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 0
fbsplash: console 1 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 1
fbsplash: console 2 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 2
fbsplash: console 3 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 3
fbsplash: console 4 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 4
fbsplash: console 5 using theme 'emergence'
fbsplash: switched splash state to 'on' on console 5
fbsplash: console 11 using theme 'livecd-2007.0'
fbsplash: switched splash state to 'on' on console 11
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized i915 1.6.0 20060119 on minor 0
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ath0: no IPv6 routers present
ath0: no IPv6 routers present
ADDRCONF(NETDEV_UP): ath0: link is not ready
ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
ADDRCONF(NETDEV_UP): ath0: link is not ready
ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
ath0: no IPv6 routers present
|
jak mam coś jeszcze dodać to piszcie 
Arfrever: Ortografia |
|
| Back to top |
|
 |
mistix
Apprentice
Joined: 27 Dec 2006
Posts: 247
Location: Gliwice / Poland
|
| Posted: Tue Nov 20, 2007 9:11 pm Post subject: |
|
|
Ja też miałem problem z hda-intel i rozwiązałem to poprzez instalację alsa-driver-9999 i cały osprzęt powiązany z alsa też w wersji niestabilnej. A w /etc/modules.d/alsa mam takie coś | Code: | options snd-hda-intel model=targa-dig
alias char-major-116 snd
alias char-major-14 soundcore
alias snd-card-0 snd-hda-intel
alias sound-slot-0 snd-hda-intel
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
options snd cards_limit=1
|
z czego najważniejsze jest odpowiednie dobranie options do swojej karty muzycznej. Głośnik zewnętrzny wyciszyłem poprzez amixer sset Surround off (tak się to śmiesznie u mnie nazywa, ale w każdym razie to głośnik może być u Ciebie inaczej). A i z kernela wywaliłem obsługę alsay i oss dodałem tylko obsługę karty dźwiękowej jako moduł i doinstalowałem zewnętrzną alse.
_________________
Cuda się zdarzają. Co potwierdzi każdy programista. |
|
| Back to top |
|
|
edoiks2
n00b
Joined: 19 Nov 2007
Posts: 6
|
| Posted: Tue Nov 20, 2007 11:50 pm Post subject: Alsa + Intel HDA z Benq R55E |
|
|
Niestety dalej nie działa, dokładnie jest tak samo, a do Conexant są tylko 2 modele test i laptop więc i tak wyboru wielkiego nie mam 
nic poczekam na następną alsę chyba, ale jak ktoś jeszcze coś wie niech pisze, |
|
| Back to top |
|
|
mistix
Apprentice
Joined: 27 Dec 2006
Posts: 247
Location: Gliwice / Poland
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Polskie forum (Polish)
