| View previous topic :: View next topic |
| Author |
Message |
kevin666a
n00b
Joined: 28 Dec 2007
Posts: 4
Location: Michigan, USA
|
 Posted: Fri Dec 28, 2007 8:54 am Post subject: Broadcom BCM4306 in master mode headache |
 |
|
iv read probably everything i could find on google, and i just cant get this thing to work in master mode.
with the bcm43xx i can get it to go in master mode and broadcast but it just broadcasts as BRCM_TEST_SSID
i am running 2.6.23-gentoo-r5 and i have tryed the b43 & b43legacy drivers but they dont even support master mode
with the bcm43xx driver it goes into master mode just fine but in dmesg i get this and it just broadcasts the BRCM_TEST_SSID
| Code: | bcm43xx driver
ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 21
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: Chip initialized
bcm43xx: 30-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
ADDRCONF(NETDEV_UP): eth2: link is not ready
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Getting essid from associate_essid
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Unable to find matching network after scan!
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 5/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: Chip initialized
bcm43xx: 30-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
ADDRCONF(NETDEV_UP): eth2: link is not ready
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Getting essid from req_essid
SoftMAC: Getting essid from req_essid
SoftMAC: Getting essid from req_essid
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Unable to find matching network after scan!
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Scanning finished: scanned 13 channels starting with channel 1
SoftMAC: Unable to find matching network after scan!
|
this is really starting to agervate me and i know theres gota be some way to get this to work by modifying some files but i dont exactaly know where to start  |
|
| Back to top |
|
 |
kevin666a
n00b
Joined: 28 Dec 2007
Posts: 4
Location: Michigan, USA
|
| Posted: Fri Dec 28, 2007 7:24 pm Post subject: |
|
|
| i guess no one knows eh? |
|
| Back to top |
|
|
kevin666a
n00b
Joined: 28 Dec 2007
Posts: 4
Location: Michigan, USA
|
| Posted: Sat Dec 29, 2007 4:39 am Post subject: |
|
|
| you people suck |
|
| Back to top |
|
|
Simba7
l33t
Joined: 22 Jan 2007
Posts: 708
Location: Billings, MT, USA
|
| Posted: Sat Dec 29, 2007 5:38 am Post subject: |
|
|
| kevin666a wrote: | | you people suck |
..and you expect to get a reply with that remark?
Maybe we're trying to see what you're talking about. Some of us try it on a test box or 'book to see if we can get the same results. My laptop was stolen with this card in it so I can't help you.
You just need to be more patient. Don't treat us like.. Erm.. Microsoft.. |
|
| Back to top |
|
|
kevin666a
n00b
Joined: 28 Dec 2007
Posts: 4
Location: Michigan, USA
|
| Posted: Sat Dec 29, 2007 7:07 am Post subject: |
|
|
| lol ok you got me there. gentoo is far from microsoft. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
