| View previous topic :: View next topic |
| Author |
Message |
maufab
n00b
Joined: 08 Feb 2006
Posts: 34
Location: Ariège
|
 Posted: Fri Jan 04, 2008 8:01 pm Post subject: [gravure] echec systématique |
 |
|
Que ce soit en ligne de commande ou bien avec k3b, j'ai systématiquement un échec de la gravure au bout de quelques temps
| Code: | System
-----------------------
K3b Version: 0.12.17
KDE Version: 3.5.7
QT Version: 3.3.8
Kernel: 2.6.22-gentoo-r5
Devices
-----------------------
PIONEER DVD-RW DVR-110D 1.22 (/dev/hdd, ) at /mnt/cdrom [CD-R; CD-RW; CD-ROM; DVD-ROM; DVD-R; DVD-RW; DVD-R DL; DVD+R; DVD+RW; DVD+R DL] [DVD-ROM; DVD-R séquentiel; DVD-R double couche séquentiel; DVD+R double couche à saut; DVD RW à réinscription limitée; DVD-RW séquentiel; DVD+RW; DVD+R; DVD+R double couche; CD-ROM; CD-R; CD-RW] [SAO; TAO; RAW; SAO/R96P; SAO/R96R; RAW/R16; RAW/R96P; RAW/R96R; Réinscription restreinte; Saut de couche]
HL-DT-ST DVDRAM GSA-H42N RL01 (/dev/hdc, ) at /mnt/cdrw [CD-R; CD-RW; CD-ROM; DVD-ROM; DVD-RAM; DVD-R; DVD-RW; DVD-R DL; DVD+R; DVD+RW; DVD+R DL] [DVD-ROM; DVD-R séquentiel; DVD-R double couche séquentiel; DVD+R double couche à saut; DVD-RAM; DVD RW à réinscription limitée; DVD-RW séquentiel; DVD+RW; DVD+R; DVD+R double couche; CD-ROM; CD-R; CD-RW] [SAO; TAO; RAW; SAO/R96P; SAO/R96R; RAW/R16; RAW/R96P; RAW/R96R; Réinscription restreinte; Saut de couche]
Used versions
-----------------------
cdrecord: 2.1.1a25
cdrecord
-----------------------
scsidev: '/dev/hdc'
devname: '/dev/hdc'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
Cdrecord-ProDVD-Clone 2.01.01a25 (x86_64-unknown-linux-gnu) Copyright (C) 1995-2006 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.9'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identifikation : 'DVDRAM GSA-H42N '
Revision : 'RL01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: CD-R
Profile: DVD-RAM
Profile: DVD-R sequential recording
Profile: DVD-R/DL sequential recording
Profile: DVD-R/DL layer jump recording
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD+RW
Profile: DVD+R
Profile: DVD+R/DL
Profile: DVD-ROM
Profile: CD-R (current)
Profile: CD-RW
Profile: CD-ROM
Profile: Removable Disk
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R LAYER_JUMP
Drive buf size : 1053696 = 1029 KB
/usr/bin/cdrecord: Success. read buffer: scsi sendcmd: no error
CDB: 3C 00 00 00 00 00 00 FC 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 71 66 62 80 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 64512
cmd finished after 0.003s timeout 200s
Drive pbuf size: 1966080 = 1920 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 144 MB
Total size: 166 MB (16:28.76) = 74157 sectors
Lout start: 166 MB (16:30/57) = 74157 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Disk Is not unrestricted
Disk Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -11824 (97:24/26)
ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 4
Manufacturer: Computer Support Italy s.r.l.
Capacity Blklen/Sparesz. Type
0 2048 No Media Present or Unknown Capacity
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 285692
Starting to write CD/DVD at speed 4 in real SAO mode for single session.
Last chance to quit, starting real write in 3 seconds.
2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Turning BURN-Free on
Performing OPC...
Sending CUE sheet...
/usr/bin/cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 144 MB written.
Track 01: 1 of 144 MB written (fifo 100%) [buf 99%] 3.4x.
Track 01: 2 of 144 MB written (fifo 100%) [buf 99%] 4.1x.
etc ...
Track 01: 65 of 144 MB written (fifo 100%) [buf 99%] 4.2x.
Track 01: 66 of 144 MB written (fifo 100%) [buf 95%] 4.1x.
/usr/bin/cdrecord: Success. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 84 5B 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A EE E0 08 80 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 63488
cmd finished after 0.138s timeout 200s
/usr/bin/cdrecord: A write error occured.
/usr/bin/cdrecord: Please properly read the error message above.
write track data: error after 69392384 bytes
Writing time: 160.436s
Average write speed 6.2x.
Min drive buffer fill was 91%
Fixating...
Fixating time: 23.961s
/usr/bin/cdrecord: fifo had 1157 puts and 1094 gets.
/usr/bin/cdrecord: fifo was 0 times empty and 1081 times full, min fill was 85%.
cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/hdc speed=6 -dao driveropts=burnfree -eject -data /home/fab/distribs/debian-40r2-amd64-netinst.iso |
et ce quel que soit le graveur utilisé.
Est-ce que quelqu'un voit d'où peut provenir ce problème?
hdparm: | Code: | hdparm /dev/hdc
/dev/hdc:
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
HDIO_GETGEO failed: Inappropriate ioctl for device |
|
|
| Back to top |
|
 |
swilmet
n00b
Joined: 14 Mar 2007
Posts: 70
Location: Belgium
|
|
| Back to top |
|
|
Tony Clifton
l33t
Joined: 07 Jul 2004
Posts: 686
Location: Rennes
|
| Posted: Sat Jan 05, 2008 7:43 pm Post subject: |
|
|
Tu as essayé avec une autre distrib ? ou même fenêtres ?
_________________
La seule certitude que j'ai, c'est d'être dans le doute ! P. Desproges |
|
| Back to top |
|
|
maufab
n00b
Joined: 08 Feb 2006
Posts: 34
Location: Ariège
|
| Posted: Mon Jan 07, 2008 5:42 pm Post subject: |
|
|
J'ai déjà essayé en root avec cdrecord sous Gentoo sans succès. J'ai essayé aussi avec une Debian Etch : résultat identique. J'en conclu que ça provient soit d'un noyau mal configuré (mais j'en doute avec 2 distribs différentes), soit d'un problème matériel avec la carte mère (Asus A8n32).
Last edited by maufab on Mon Jan 07, 2008 5:49 pm; edited 2 times in total |
|
| Back to top |
|
|
dapsaille
Advocate
Joined: 02 Aug 2004
Posts: 2366
Location: Paris
|
| Posted: Mon Jan 07, 2008 5:43 pm Post subject: |
|
|
| Ou un graveur hs ^^ plus de "chances" que la carte maman |
|
| Back to top |
|
|
maufab
n00b
Joined: 08 Feb 2006
Posts: 34
Location: Ariège
|
| Posted: Mon Jan 07, 2008 5:45 pm Post subject: |
|
|
| Non, ce n'est pas celà car j'avais déjà racheté un nouveau graveur dans une autre marque (l'ancien, toujours en place un pioneer 110, le nouveau un LG). Il me reste à essayer sous winxp. |
|
| Back to top |
|
|
dapsaille
Advocate
Joined: 02 Aug 2004
Posts: 2366
Location: Paris
|
| Posted: Mon Jan 07, 2008 5:54 pm Post subject: |
|
|
Changer de nappe/alimentation ...
test mémoire ..
Changer le canal ide/ tester avec un adaptateur ide>sata si tu as tu sata ..
ouaips beaucoup de possibilité :p
avec l'ancien tu avais les memes erreurs (exactement je veux dire) ? |
|
| Back to top |
|
|
maufab
n00b
Joined: 08 Feb 2006
Posts: 34
Location: Ariège
|
| Posted: Mon Jan 07, 2008 6:07 pm Post subject: |
|
|
oui, les mêmes erreurs : un début de gravure puis échec et éjection du cd. Je vais tenter tes solutions.
merci |
|
| Back to top |
|
|
|
French
