View previous topic :: View next topic |
Author |
Message |
<3 Veteran
Joined: 21 Oct 2004 Posts: 1081
|
Posted: Wed Jan 09, 2008 5:30 pm Post subject: How do I enable SPDIF (optical) [solved] |
|
|
I am trying to enable SPDIF (optical) from my on board sound card but I can't figure out how to go about enabling it. I have a Abit KN8 SLI motherboard with a Nforce 4 SLI chipset running ALSA.
lspci wrote: | 00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2) |
cat /proc/asound/cards wrote: | 0 [CK804 ]: NFORCE - NVidia CK804
NVidia CK804 with ALC850 at irq 23 |
lsmod wrote: | snd_intel8x0 31080 3
snd_ac97_codec 108312 1 snd_intel8x0
ac97_bus 2624 1 snd_ac97_codec
snd_pcm 70412 4 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 18760 2 snd_seq,snd_pcm
snd 50600 14 snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc 8208 2 snd_intel8x0,snd_pcm
snd_pcm_oss 25664 0
snd_mixer_oss 14592 1 snd_pcm_oss
snd_seq_dummy 3268 0
snd_seq_oss 27904 0
snd_seq_midi_event 6528 1 snd_seq_oss
snd_seq 44576 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 6868 3 snd_seq_dummy,snd_seq_oss,snd_seq |
Right now I am getting audio through the analog jacks fine but I want to switch to SPDIF. When I connect my Logitech z-680 5.1 speaker set to the SPDIF port the Display on the control panel of the speakers say " Input: Optical No Digital Data". But I am able to get SPDIF working in windows XP.
Last edited by <3 on Thu Jan 10, 2008 8:41 am; edited 1 time in total |
|
Back to top |
|
|
Karlhungus Tux's lil' helper
Joined: 19 Jun 2005 Posts: 79 Location: Halifax, Nova Scotia
|
Posted: Wed Jan 09, 2008 7:16 pm Post subject: |
|
|
Try [url]http://gentoo-wiki.com/HOWTO_Dolby_Digital_Out_(AC3,_SPDIF)[/url]. I've had luck running 5.1 sound via mplayer over spdif using this. Haven't been able to make it work in mythtv yet, or set it as the default output (put much effort into this yet however).
EDIT: not sure why that url isn't showing up. |
|
Back to top |
|
|
<3 Veteran
Joined: 21 Oct 2004 Posts: 1081
|
Posted: Wed Jan 09, 2008 8:59 pm Post subject: |
|
|
OK just tried that and now my reciever is detecting that the SPDIF is working but no sound is comming out and now the analog sound put isn't working either. I've already tried un muting and turning up the sound to max in alsamixer (at least I think I did).
p.s.
The reason why your link isn't showing properly probably has to do with the fact that your link has special chars in it. |
|
Back to top |
|
|
<3 Veteran
Joined: 21 Oct 2004 Posts: 1081
|
Posted: Thu Jan 10, 2008 8:41 am Post subject: |
|
|
OK figured it out. After you follow the instructions in that post you need to set the IEC958 Playback source as Analog In in alsamixer. |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|