| View previous topic :: View next topic |
| Author |
Message |
sh0r7y
n00b
Joined: 11 Jun 2008
Posts: 7
|
 Posted: Sun Jun 15, 2008 4:23 pm Post subject: probleme mit WLan Intel 3945ABG |
 |
|
Tach ich versuch jetzt seit längeren auf meinem Dell Inspiron 1720 dass Wlan zum laufen zu bringen.
ich hab mich an dass HowTo von Gentoo-Wiki gehalten.
kernel verwende ich den 2.6.24-gentoo-r8
ich bekomm jedoch keine verbindung zu meinem Speedport 700 V zustanden egal ob ich es ungesichert versuche oder mit WPA
hier mal meine wpa_supplicant.conf
| Code: |
#Open
network={
ssid="meine_SSID"
key_mgmt=NONE
priority=2
}
|
dann meine net
| Code: |
config_eth0=( "dhcp" )
dhcpcd_eth0="-t 30"
modules=( "wpa_supplicant" )
wpa_supplicant_wlan0="-Dndiswrapper"
wpa_timeout_eth1=60
config_wlan0=( "dhcp" )
config_wlan0="-t 30"
|
und dann noch die ausgabe von
wpa_supplicant -Dndiswrapper -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -dd
| Code: |
wpa_supplicant -Dndiswrapper -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'ndiswrapper' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ap_scan=2
Line: 7 - start of a new network block
ssid - hexdump_ascii(len=10):
73 68 30 72 37 79 57 4c 61 6e meine_ssid
key_mgmt: 0x4
Priority group 0
id=0 ssid='meine_ssid'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:1c:bf:51:87:2f
Driver does not support WPA.
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
Ignore event for foreign ifindex 3
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Trying to associate with SSID 'meine_ssid'
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Association request to the driver failed
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=ForceAuthorized
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Trying to associate with SSID 'meine_ssid'
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Association request to the driver failed
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=ForceAuthorized
CCTRL-EVENT-TERMINATING - signal 2 received
|
MFG |
|
| Back to top |
|
 |
py-ro
Veteran
Joined: 24 Sep 2002
Posts: 1734
Location: Velbert
|
| Posted: Sun Jun 15, 2008 6:11 pm Post subject: |
|
|
| Quote: | | ich hab mich an dass HowTo von Gentoo-Wiki gehalten |
Ist die Karte da? ifconfig -a
| Quote: | | Code: | | wpa_supplicant_wlan0="-Dndiswrapper" |
|
Ds kann nicht stimmen müsste -Dwext sein, ohne jetzt nachgeschaut zu haben.
Ansonsten fehlt noch welches Modul du benutzt, hast du die Firmware isntalliert, was sagt dmesg beim laden des Moduls?
Py |
|
| Back to top |
|
|
sh0r7y
n00b
Joined: 11 Jun 2008
Posts: 7
|
| Posted: Sun Jun 15, 2008 8:09 pm Post subject: |
|
|
also modul benutze ich das iwl3945
und sie wird auch bei ifconfig -a angezeigt.
| Code: |
lo Link encap:Local Loopback
LOOPBACK MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:1C:BF:51:87:2F
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wmaster0 Link encap:UNSPEC HWaddr 00-1C-BF-51-87-2F-38-80-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
|
und dmesg spricht
| Code: |
sh0r7y@linux ~ $ dmesg | grep iwl
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.1.17ks
iwl3945: Copyright(c) 2003-2007 Intel Corporation
iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
phy0: Selected rate control algorithm 'iwl-3945-rs'
|
ich habe es auch schon versucht mit -Dwext
da kommt dann beim restarten vom wlan
| Code: |
* Starting wlan0
* Wireless radio has been killed for interface wlan0
* wpa_supplicant will launch, but not associate until
* wireles radio is re-enabled for interface wlan0
* Starting wpa_supplicant on wlan0 ...
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAUTH]: Operation not supported [ ok ]th param 5 value 0x1 -
* Starting wpa_cli on wlan0 ... [ ok ]
* Backgrounding ...
|
und firmware wir durch
emerge iwl3945-ucode
installiert |
|
| Back to top |
|
|
astaecker
Guru
Joined: 28 Apr 2003
Posts: 403
Location: Hamburg / Germany
|
| Posted: Mon Jun 16, 2008 7:34 am Post subject: |
|
|
| sh0r7y wrote: | | Code: |
* Wireless radio has been killed for interface wlan0
* wpa_supplicant will launch, but not associate until
* wireles radio is re-enabled for interface wlan0
|
|
Kann es sein, dass der WLan-Schalter an der linken Seite von deinem Notebook auf "Aus" geschaltet ist? |
|
| Back to top |
|
|
sh0r7y
n00b
Joined: 11 Jun 2008
Posts: 7
|
| Posted: Mon Jun 16, 2008 8:01 am Post subject: |
|
|
nein der ist ein.
weil ich kann über
iwconfig wlan0 txpower on
das wlan auch wieder einschalten. |
|
| Back to top |
|
|
|
Deutsches Forum (German)
