| View previous topic :: View next topic |
| Author |
Message |
GentooMan
n00b
Joined: 21 Jul 2007
Posts: 13
|
 Posted: Fri Aug 01, 2008 9:00 am Post subject: Problems booting SATA II, ata_piix driver |
 |
|
Hi everyone,
After some no-gentoo time, i've decided to go back to the origin... 
Last time i tried gentoo, it was early 2007 kernel & distro (i used minimal installation disc then).
A few days ago, when i installed gentoo again, it would'nt boot,
Here is my lspci
| Code: |
00:00.0 Host bridge: Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub (rev 81)
00:01.0 PCI bridge: Intel Corporation 945G/GZ/P/PL Express PCI Express Root Port (rev 81)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller IDE (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc R520 [Radeon X1800]
01:00.1 Display controller: ATI Technologies Inc R520 [Radeon X1800] (Secondary)
03:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5789 Gigabit Ethernet PCI Express (rev 11)
04:02.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
04:02.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
|
And the SATA Driver, according to it, is:
| Code: |
808627c0 Yes Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller IDE ata_piix
|
How should i configure my kernel to get gentoo boot?
Thank's 
_________________
The past is history,
The future is mystery,
This moment is a gift - thats why we call it "present" 
|
|
| Back to top |
|
 |
tmasscool
Apprentice
Joined: 27 Jul 2005
Posts: 151
|
| Posted: Fri Aug 01, 2008 10:14 am Post subject: |
|
|
| Code: |
Device Drivers --->
SCSI device support --->
<*> SCSI disk support
<*> Serial ATA (prod) and Parallel ATA (experimental) drivers
[*] ATA ACPI Support
[*] ATA SFF support
<*> Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support
|
You can add other drivers like scsi cdrom support, but this should be sufficient for booting..
Don't forget to edit your grub.conf and add root=/dev/sdYX as kernel option, where /dev/sdYX as your / partition... |
|
| Back to top |
|
|
snocer
n00b
Joined: 02 Dec 2007
Posts: 6
|
| Posted: Sun Aug 03, 2008 7:38 am Post subject: |
|
|
Hi!
I have a similar Problem on a Dell XPS Laptop with the same driver. My system boots at most every fourth try.
My Chipset is a ICH8M but maybe its the same problem with the driver and it will help to find a solution.
The kernel boot stops here:
| Code: | ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH8M: IDE controller (0x8086:0x2850 rev 0x02) at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ICH8M: not 100% native mode: will probe irqs later
ICH8M: IDE port disabled
|
and sometimes its resumed with this:
| Code: | ide0: BM-DMA at 0x6fa0-0x6fa7, BIOS settings: hda:DMA, hdb:PIO
Probing IDE interface ide0...
hda: Optiarc DVD+/-RW AD-7640A, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
|
I seem it helps to push the cd eject button prior the boot process so the cd-drive is "active and at work" on kernel probe.
Maybe your problem is the same?
Greetings
Claas |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
