View previous topic :: View next topic |
Author |
Message |
keola n00b
Joined: 22 Feb 2005 Posts: 53
|
Posted: Sun Aug 31, 2008 2:54 am Post subject: Grub Issues - [solved] |
|
|
I have tried now on two drives - both are the same model though. I blew through an install without the guide (which I never need anyway) and the drive didn't appear to be bootable. I booted off the livecd and reinstalled grub... no luck, cleared the MBR, tried to install grub manually and with grub-install.
So I got another drive, walked through the install with the handbook and I have the same issue. I have checked everything in the BIOS and even wiped the drive clean and started over. I can put the old drive (older smaller drive) in and it boots just fine.
Anyone have any idea of what may be going wrong?
Thanks
Last edited by keola on Mon Sep 01, 2008 3:50 am; edited 1 time in total |
|
Back to top |
|
|
kevstar31 Guru
Joined: 22 Nov 2006 Posts: 449 Location: Ohio
|
Posted: Sun Aug 31, 2008 3:06 am Post subject: |
|
|
try using grub shell to install grub by booting from a knoppix livecd an type: sudo grub
Once in the shell type : find /boot/grub/stage1
For the partition stage 1 is found on type root (hdx,x)
Then setup (hdx) _________________ while(true) std::cout << "Jesus I trust in you." << std::endl;
My Political Compass |
|
Back to top |
|
|
keola n00b
Joined: 22 Feb 2005 Posts: 53
|
Posted: Sun Aug 31, 2008 3:16 am Post subject: |
|
|
I don't see how that would be any different from using a livecd and trying to install it again. it is a single disk config, so it is hd(0,0) and (hd0)... I may try it tomorrow. I have to get to bed for now. |
|
Back to top |
|
|
kevstar31 Guru
Joined: 22 Nov 2006 Posts: 449 Location: Ohio
|
Posted: Sun Aug 31, 2008 3:34 am Post subject: |
|
|
So i can see if errors show up. post your fstab and grub.conf _________________ while(true) std::cout << "Jesus I trust in you." << std::endl;
My Political Compass |
|
Back to top |
|
|
keola n00b
Joined: 22 Feb 2005 Posts: 53
|
Posted: Sun Aug 31, 2008 3:52 am Post subject: |
|
|
had a sec to complete the op... installed grub via knoppix, no issues, same results as installing from livecd, as well as no boot. |
|
Back to top |
|
|
keola n00b
Joined: 22 Feb 2005 Posts: 53
|
Posted: Sun Aug 31, 2008 4:04 am Post subject: |
|
|
I think my issue is solved. These drives were from a raid set, I assumed zeroing out the first 100mb would wipe that out. Just by chance I looked in the raid config (as these drives were from a diff. comp and diff. raid controller) and it was reporting an incomplete set. after wiping that, all my partitions are gone. So I can assume it will boot once I reinstall. I will update tomorrow. |
|
Back to top |
|
|
keola n00b
Joined: 22 Feb 2005 Posts: 53
|
Posted: Sun Aug 31, 2008 11:09 pm Post subject: |
|
|
That did it... I have never had that problem before... it didn't come to mind to check because the controllers were different brands, but the obviously use the same 'software'. I was very surprised to see an incomplete raid set in the config screen... |
|
Back to top |
|
|
kevstar31 Guru
Joined: 22 Nov 2006 Posts: 449 Location: Ohio
|
Posted: Mon Sep 01, 2008 12:45 am Post subject: |
|
|
Plese add [solved] to the end of the subject line of your orignal post. _________________ while(true) std::cout << "Jesus I trust in you." << std::endl;
My Political Compass |
|
Back to top |
|
|
|