| View previous topic :: View next topic |
| Author |
Message |
nero37
Tux's lil' helper
Joined: 15 Jun 2007
Posts: 141
Location: Ireland
|
 Posted: Wed Dec 17, 2008 10:10 pm Post subject: [Solved]rtorrent; delete file on erase |
 |
|
hi, I'm trying to get rtorrent to delete the torrent data when i erase the torrent from within rtorrent.
tried this in ~/.rtorrent.rc
| Code: | | on_erase = remove_file,"execute=rm,-rf,$d.get_base_path=" |
for some reason this isn't working. "on_erase" is getting called but its not removing the data. anyone got any ideas?
full ~/.rtorrent.rc
| Code: | scgi_port = localhost:5000
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.
# Maximum and minimum number of peers to connect to per torrent.
#min_peers = 40
#max_peers = 100
# Same as above but for seeding completed torrents (-1 = same as downloading)
#min_peers_seed = 10
#max_peers_seed = 50
# Maximum number of simultanious uploads per torrent.
max_uploads = 5
# Global upload and download rate in KiB. "0" for unlimited.
download_rate = 0
upload_rate = 24
# Default directory to save the downloaded torrents.
directory = /home/rtorrent/downloads/
# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = ~/downloads/session
# Watch a directory for new torrents, and stop those that have been
# deleted.
#schedule = watch_directory,5,5,load_start=./watch/*.torrent
#schedule = untied_directory,5,5,stop_untied=
# Close torrents when diskspace is low.
schedule = low_diskspace,5,60,close_low_diskspace=100M
# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
schedule = ratio,60,60,"stop_on_ratio=150,200M,2000"
# The ip address reported to the tracker.
#ip = 127.0.0.1
#ip = rakshasa.no
# The ip address the listening socket and outgoing connections is
# bound to.
#bind = 127.0.0.1
#bind = rakshasa.no
# Port range to use for listening.
port_range = 45450-45460
# Start opening ports at a random position within the port range.
port_random = no
# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
check_hash = yes
# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = yes
# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa
# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
encryption = allow_incoming,enable_retry,prefer_plaintext
# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
dht = auto
# UDP port to use for DHT.
#
dht_port = 45461
# Enable peer exchange (for torrents not marked private)
#
peer_exchange = yes
#
# Do not modify the following parameters unless you know what you're doing.
#
# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10
# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100
# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10
#Custum shit
#schedule upload speed so its fast at night when you should be asleep
schedule = throttle_1,02:00:00,24:00:00,upload_rate=0
schedule = throttle_2,08:00:00,24:00:00,upload_rate=24
#move compleated
on_finished = move_complete,"execute=cp,-u,$d.get_base_path=,/mnt/data/"
#remove file
on_erase = remove_file,"execute=rm,-rf,$d.get_base_path=" |
Thanks
Last edited by nero37 on Wed Jan 07, 2009 1:09 pm; edited 1 time in total |
|
| Back to top |
|
 |
v4lkyrius
n00b
Joined: 21 Dec 2008
Posts: 1
Location: Toronto
|
| Posted: Sun Dec 21, 2008 10:18 pm Post subject: Re: rtorrent; delete file on erase |
|
|
Instead of copying and then deleting, just move the files (reference):
| Code: | | on_finished = move_complete,"d.set_directory=~/Download/ ;execute=mv,-u,$d.get_base_path=,/mnt/data/" |
Although, the on_erase line you're looking for might be:
| Code: | | on_erase = remove_file,"execute={rm,-drf,--,$d.get_base_path=}" |
|
|
| Back to top |
|
|
nero37
Tux's lil' helper
Joined: 15 Jun 2007
Posts: 141
Location: Ireland
|
| Posted: Tue Dec 23, 2008 4:10 am Post subject: |
|
|
| Thanks, I have it working now. Your version of the erase worked. The reason I'm not moving the file, is that it is being moved out to a external hd and don't want this to be used as the active directory for the torrent. The hds used in a lot of external drives are often of lower quality and I don't want rtorrent constantly reading from it. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
