| View previous topic :: View next topic |
| Author |
Message |
Kate Monster
Apprentice
Joined: 13 Jun 2006
Posts: 226
Location: Clarkston, Michigan
|
 Posted: Sat Feb 14, 2009 6:22 am Post subject: Hauppauge HVR 1950 |
 |
|
Hi, I am having issues trying to get my TV tuner working. I know for a fact analog isn't working, but I can't tell if digital works or not, it acts like it can't ever find a signal(this is QAM, btw), but I have a feeling some other brokenness could be to blame. Here is the relevant snippet of dmesg:
| Code: | usbcore: registered new interface driver pvrusb2
pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner
pvrusb2: Debug mask is 31 (0x1f)
cx25840' 1-0044: cx25843-24 found @ 0x88 (pvrusb2_a)
tuner' 1-0042: chip found @ 0x84 (pvrusb2_a)
tveeprom 1-00a2: Hauppauge model 75111, rev C3E9, serial# 5072332
tveeprom 1-00a2: MAC address is 00-0D-FE-4D-65-CC
tveeprom 1-00a2: tuner model is Philips 18271_8295 (idx 149, type 54)
tveeprom 1-00a2: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
tveeprom 1-00a2: audio processor is CX25843 (idx 37)
tveeprom 1-00a2: decoder processor is CX25843 (idx 30)
tveeprom 1-00a2: has radio, has IR receiver, has IR transmitter
pvrusb2: Supported video standard(s) reported available in hardware: PAL-M/N/Nc;NTSC-M/Mj/Mk;ATSC-8VSB/16VSB
pvrusb2: Mapping standards mask=0x300b700 (PAL-M/N/Nc;NTSC-M/Mj/Mk;ATSC-8VSB/16VSB)
pvrusb2: Setting up 6 unique standard(s)
pvrusb2: Set up standard idx=0 name=PAL-M
pvrusb2: Set up standard idx=1 name=PAL-N
pvrusb2: Set up standard idx=2 name=PAL-Nc
pvrusb2: Set up standard idx=3 name=NTSC-M
pvrusb2: Set up standard idx=4 name=NTSC-Mj
pvrusb2: Set up standard idx=5 name=NTSC-Mk
pvrusb2: Initial video standard (determined by device type): NTSC-M
pvrusb2: Device initialization completed successfully.
pvrusb2: registered device video0 [mpeg]
DVB: registering new adapter (pvrusb2-dvb)
tda829x 1-0042: setting tuner address to 60
tda18271 1-0060: creating new instance
TDA18271HD/C1 detected @ 1-0060
tda829x 1-0042: type set to tda8295+18271
cx25840' 1-0044: firmware: requesting v4l-cx25840.fw
cx25840' 1-0044: loaded v4l-cx25840.fw firmware (12559 bytes)
fuse init (API version 7.10)
cx25840' 1-0044: Video signal: not present
cx25840' 1-0044: Detected format: NTSC-M
cx25840' 1-0044: Specified standard: NTSC-M
cx25840' 1-0044: Specified video input: Composite 7
cx25840' 1-0044: Specified audioclock freq: 48000 Hz
cx25840' 1-0044: Detected audio mode: mono
cx25840' 1-0044: Detected audio standard: BTSC
cx25840' 1-0044: Audio muted: no
cx25840' 1-0044: Audio microcontroller: detecting
cx25840' 1-0044: Configured audio standard: automatic detection
cx25840' 1-0044: Configured audio system: BTSC
cx25840' 1-0044: Specified audio input: Tuner (In8)
cx25840' 1-0044: Preferred audio mode: stereo
cx25840' 1-0044: firmware: requesting v4l-cx25840.fw
cx25840' 1-0044: loaded v4l-cx25840.fw firmware (12559 bytes)
e1000e 0000:00:19.0: irq 1277 for MSI/MSI-X
e1000e 0000:00:19.0: irq 1277 for MSI/MSI-X
usb 1-2: firmware: requesting v4l-cx2341x-enc.fw
cx25840' 1-0044: 0x0000 is not a valid video input!
DVB: registering adapter 0 frontend 1 (Samsung S5H1411 QAM/8VSB Frontend)...
tda829x 1-0042: type set to tda8295
tda18271 1-0060: attaching existing instance |
Everything looks fine, I can't figure it out. The only suspect line is | Code: | | cx25840' 1-0044: 0x0000 is not a valid video input! |
but I am unsure how to proceed. Trying to run cat /dev/video, mplayer tv://, or tvtime all fail complaining that the operation is not permitted. I am running the pvrusb2 module from gentoo-sources-2.6.28. I have all the firmware files, or am pretty sure I do, the driver doesn't complain about anything. What should I do? |
|
| Back to top |
|
 |
Nicias
Guru
Joined: 06 Dec 2005
Posts: 446
|
| Posted: Sat Feb 14, 2009 5:00 pm Post subject: |
|
|
| I suggest trying vanilla sources. If that doesn't work, post to the prvusb2 mailing list. The list is very helpful. |
|
| Back to top |
|
|
Kate Monster
Apprentice
Joined: 13 Jun 2006
Posts: 226
Location: Clarkston, Michigan
|
| Posted: Tue Feb 17, 2009 4:20 pm Post subject: |
|
|
| Nicias wrote: | | I suggest trying vanilla sources. |
I'll give it a shot I suppose, but what is so different about the vanilla sources? | Quote: | | If that doesn't work, post to the prvusb2 mailing list. The list is very helpful. |
ok, I'll go ahead and post this there. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Multimedia
