cdrdao help

j7899 · n00b Joined: 16 May 2002 Posts: 30

I just installed K3B .7 and it seems like a nice program, but I cant burn CD's. In the consol I type cdrdao disk-info and get the following:

Cdrdao version 1.1.5 - (C) Andreas Mueller
SCSI interface library - (C) Joerg Schilling
L-EC encoding library - (C) Heiko Eissfeldt
Paranoia DAE library - (C) Monty

Check »cdrdao.sourceforge.net/drives.html#dt[?] for current driver tables.

Using libscg version 'schily-0.5'

/dev/cdrecorder: SONY CD-RW CRX160E Rev: 1.0e
ERROR: No driver found for 'SONY CD-RW CRX160E', available drivers:
cdd2600
generic-mmc
generic-mmc-raw
plextor
plextor-scan
ricoh-mp6200
sony-cdu920
sony-cdu948
taiyo-yuden
teac-cdr55
toshiba
yamaha-cdr10x
ERROR: Cannot setup device /dev/cdrecorder.

Ok I know my burner is supported and is listed to use generic-mmc, which I tell the K3B to use, but I still get this error? /dev/cdrecorder points to /dev/scsi/host0/bus0/target0/lun0/cd , where in /dev/scsi/host0/bus0/target0/lun0 there is a block device 'cd', and a 'generic Character device'.

Any ideas?

BinaryAlchemy · n00b Joined: 31 May 2002 Posts: 42 Location: Ca, US

Try pointing /dev/cdrecorder to the sg device instead?

j7899 · n00b Joined: 16 May 2002 Posts: 30

/dev/cdrecorder points to the correct device, sr0 points to the same thing /dev/cdrecorder points to, I added /dev/cdrecorder to satisfy cdrdao, which worked and didn't.

BinaryAlchemy · n00b Joined: 31 May 2002 Posts: 42 Location: Ca, US

No. /dev/cdrecorder needs to point to /dev/scsi/host0/bus0/target0/lun0/generic NOT /dev/scsi/host0/bus0/target0/lun0/cd. The cd device is for using it as a cdrom, the burner needs to use raw scsi commands. Which go through the generic device.

j7899 · n00b Joined: 16 May 2002 Posts: 30

I switched it so /dev/cdrecorder points to /dev/sg0 which points to generic.

Here is my output error from k3b trying to use cdrdao

drdao
-----------------------
Cdrdao version 1.1.5 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
L-EC encoding library - (C) Heiko Eissfeldt
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'schily-0.5'
0,0,0: SONY CD-RW CRX160E Rev: 1.0e
Using driver: Generic SCSI-3/MMC - Version 1.2 (options 0x0010)
Starting write simulation at speed 8...
Process can be aborted with QUIT signal (usually CTRL-\).
?: Input/output error. : scsi sendcmd: no error
CDB: 5D 00 00 00 00 00 00 00 20 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 12 00 00 00 00 26 00 00 80
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x26 Qual 0x00 (invalid field in parameter list) Fru 0x0
Sense flags: Blk 0 (not valid) error refers to data part, bit ptr 0 (not valid) field ptr 0
cmd finished after 0.274s timeout 180s
ERROR: Cannot send cue sheet.
ERROR: Simulation failed.

j7899 · n00b Joined: 16 May 2002 Posts: 30

I just realized I was only trying to simulate-write audio, I tried a sim-data and it worked fine, I wonder what the problem is with audio, is k3b just sensitive to audio?

sy5tematic · n00b Joined: 31 May 2002 Posts: 15

rac · Posted: Wed Aug 21, 2002 11:09 am Post subject:

Fled the crowds in Desktop Environments for the wide open spaces of the new Multimedia forum.
_________________
For every higher wall, there is a taller ladder