| View previous topic :: View next topic |
| Author |
Message |
h2sammo
Veteran
Joined: 11 Mar 2009
Posts: 1025
Location: Michigan
|
 Posted: Sat Mar 13, 2010 4:32 pm Post subject: Error inserting it87 module |
 |
|
| Code: | main bobby # lsmod
Module Size Used by
i2c_dev 7784 0
radeon 375456 2
drm 175136 3 radeon
snd_pcm_oss 44192 0
snd_mixer_oss 19448 1 snd_pcm_oss
snd_seq_oss 32224 0
snd_seq_midi_event 7608 1 snd_seq_oss
snd_seq 57376 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 7436 2 snd_seq_oss,snd_seq
b43 128040 0
ssb 39208 1 b43
forcedeth 60900 0
i2c_nforce2 8000 0
k8temp 5560 0
main bobby # modprobe it87
FATAL: Error inserting it87 (/lib/modules/2.6.31-gentoo-r6/kernel/drivers/hwmon/it87.ko): Device or resource busy |
i have installed lm_sensors and run sensors-detect:
| Code: | Found `ITE IT8716F Super IO Sensors' Success!
(address 0x290, driver `it87') |
what is the error due to?
i made that sensor a module in kernel.
| Code: | main bobby # dmesg | grep it87
[ 15.867324] it87: Found IT8716F chip at 0x290, revision 0
[ 15.867333] it87: in3 is VCC (+5V)
[ 15.867335] it87: in7 is VCCH (+5V Stand-By)
[ 15.867396] ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region IP__ [0x295-0x296] |
|
|
| Back to top |
|
 |
haarp
Guru
Joined: 31 Oct 2007
Posts: 535
|
|
| Back to top |
|
|
saellaven
l33t
Joined: 23 Jul 2006
Posts: 655
|
| Posted: Sun Mar 14, 2010 7:03 pm Post subject: |
|
|
Assuming an Asus motherboard,
ACPI says the resources are already reserved, in this case for the asus_atk0110 driver. The 2.6.31 kernel is more strict about handing over control to another driver now and would prefer that the atk0110 driver handle sensor data. The proper fix is to enable CONFIG_SENSORS_ATK0110, disable CONFIG_SENSORS_IT87 and upgrade to lm_sensors-3.1.1.
Failing that, add acpi_enforce_resources=lax to your kernel's boot options (this is the wrong way to do it, but will return the previous behavior).
_________________
Ryzen 3700X, Asus Prime X570-Pro, 64 GB DDR4 3200, GeForce GTX 1660 Super
openrc-0.17, ~vanilla-sources, ~nvidia-drivers, ~gcc |
|
| Back to top |
|
|
h2sammo
Veteran
Joined: 11 Mar 2009
Posts: 1025
Location: Michigan
|
| Posted: Fri Mar 19, 2010 1:10 am Post subject: |
|
|
my mobo is a DFI NF590 SLI-M2R/G.
i could not find anything about it in the kernel...
is there a way to allow it87 sensor modules on this board? |
|
| Back to top |
|
|
saellaven
l33t
Joined: 23 Jul 2006
Posts: 655
|
| Posted: Fri Mar 19, 2010 2:30 am Post subject: |
|
|
you should be able to get the old behavior back if you add acpi_enforce_resources=lax to your boot options.
lm-sensors.org appears to be down right now, so I can't see if there is an ACPI driver available for your motherboard or if there are still only Asus ACPI drivers.
_________________
Ryzen 3700X, Asus Prime X570-Pro, 64 GB DDR4 3200, GeForce GTX 1660 Super
openrc-0.17, ~vanilla-sources, ~nvidia-drivers, ~gcc |
|
| Back to top |
|
|
h2sammo
Veteran
Joined: 11 Mar 2009
Posts: 1025
Location: Michigan
|
| Posted: Fri Mar 19, 2010 8:28 pm Post subject: |
|
|
i used acpi_enforce_resources=lax in boot.config and now i get tons more info, thank you:
| Code: | bobby@main ~ $ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:
+36 C
Core1 Temp:
+34 C
it8716-isa-0290
Adapter: ISA adapter
VCore: +1.30 V (min = +0.00 V, max = +4.08 V)
VDDR: +1.31 V (min = +0.00 V, max = +4.08 V)
+3.3V: +1.22 V (min = +0.00 V, max = +4.08 V)
+5V: +4.84 V (min = +0.00 V, max = +6.85 V)
+12V: +11.97 V (min = +0.00 V, max = +16.32 V)
in5: +1.44 V (min = +0.00 V, max = +4.08 V)
in6: +1.84 V (min = +0.00 V, max = +4.08 V)
5VSB: +4.81 V (min = +0.00 V, max = +6.85 V)
VBat: +3.12 V
fan1: 3214 RPM (min = 3245 RPM) ALARM
fan2: 0 RPM (min = 3245 RPM) ALARM
fan3: 0 RPM (min = 3245 RPM) ALARM
temp1: +54 C (low = +127 C, high = +84 C) sensor = diode
temp2: +43 C (low = +127 C, high = +84 C) sensor = invalid
temp3: +84 C (low = +127 C, high = +84 C) sensor = invalid ALARM
vid: +1.550 V |
if i use the stable lm_sensors i get what you see above. if I unmask it, i get:
| Code: | bobby@main ~ $ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +53.0 C (crit = +84.0 C)
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +35.0 C
Core1 Temp: +32.0 C
it8716-isa-0290
Adapter: ISA adapter
in0: +1.30 V (min = +0.00 V, max = +4.08 V)
in1: +1.31 V (min = +0.00 V, max = +4.08 V)
in2: +1.22 V (min = +0.00 V, max = +4.08 V)
in3: +2.88 V (min = +0.00 V, max = +4.08 V)
in4: +2.99 V (min = +0.00 V, max = +4.08 V)
in5: +1.44 V (min = +0.00 V, max = +4.08 V)
in6: +1.84 V (min = +0.00 V, max = +4.08 V)
in7: +2.86 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.12 V
fan1: 3214 RPM (min = 3245 RPM)
fan2: 0 RPM (min = 3245 RPM)
fan3: 0 RPM (min = 3245 RPM)
temp1: +53.0 C (low = +127.0 C, high = +84.0 C) sensor = thermal diod
temp2: +42.0 C (low = +127.0 C, high = +84.0 C) sensor = thermistor
temp3: +81.0 C (low = +127.0 C, high = +84.0 C) sensor = thermistor
cpu0_vid: +1.550 V
|
but there is the following error every time i start the unmasked program:
| Code: | | /etc/sensors.conf does not exist |
|
|
| Back to top |
|
|
Cyker
Veteran
Joined: 15 Jun 2006
Posts: 1746
|
| Posted: Sat Mar 20, 2010 8:06 am Post subject: |
|
|
General warning:
Be careful if you disable IT87 module; This disables fan control and depending on the motherboard and BIOS, this may also stop (some of) the fans from running! 
The ATK ACPI driver has NO support for changing the fan duty cycle at the moment, so the acpi=lax is required if you need software fan control. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
