| View previous topic :: View next topic |
| Author |
Message |
johnny99
Apprentice
Joined: 24 Oct 2005
Posts: 252
Location: Berkeley, California
|
 Posted: Fri Apr 02, 2010 4:58 pm Post subject: ath5k apm wakeup tx off |
 |
|
When my laptop wakes from sleep (acpitools -s), the wireless nic (ath5k module) tx power is set to off.
Io activate I must run:
| Code: | /etc/init.d/net.wlan0 stop
iwconfig wlan0 tx on
/etc/init.d/net.wlan0 start |
What is the proper way to fix this?
network scirpts, hal, dbus, acpi, something else?
lspci |grep Eth
| Code: | 00:19.0 Ethernet controller: Intel Corporation 82566MM Gigabit Network Connection (rev 03)
03:00.0 Ethernet controller: Atheros Communications Inc. AR5212 802.11abg NIC (rev 01) |
sys-power/acpitool-0.4.7-r1
modinfo ath5k
| Code: |
filename: /lib/modules/2.6.31-gentoo-r6/kernel/drivers/net/wireless/ath/ath5k/ath5k.ko
version: 0.6.0 (EXPERIMENTAL)
license: Dual BSD/GPL
description: Support for 5xxx series of Atheros 802.11 wireless LAN cards.
author: Nick Kossifidis
author: Jiri Slaby
srcversion: 4CC5921A00F32232A640E9F
alias: pci:v0000168Cd0000001Dsv*sd*bc*sc*i*
alias: pci:v0000168Cd0000001Csv*sd*bc*sc*i*
alias: pci:v0000168Cd0000001Bsv*sd*bc*sc*i*
alias: pci:v0000168Cd0000001Asv*sd*bc*sc*i*
alias: pci:v0000168Cd00000019sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000018sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000017sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000016sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000015sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000014sv*sd*bc*sc*i*
alias: pci:v0000168Cd00001014sv*sd*bc*sc*i*
alias: pci:v000010B7d00000013sv*sd*bc*sc*i*
alias: pci:v0000A727d00000013sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000013sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000012sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000011sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000007sv*sd*bc*sc*i*
alias: pci:v0000168Cd00000207sv*sd*bc*sc*i*
depends: mac80211,cfg80211,ath
vermagic: 2.6.31-gentoo-r6 SMP mod_unload modversions 686 4KSTACKS
parm: nohwcrypt:Disable hardware encryption. (bool)
parm: all_channels:Expose all channels the device can use. (bool) |
dmesg around the sleep/wake event:
| Code: | Extended CMOS year: 2000
Back to C!
CPU0: Thermal monitoring handled by SMI
Extended CMOS year: 2000
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
CPU 1 irqstacks, hard=c1fda000 soft=c1fdb000
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4389.50 BogoMIPS (lpj=21947534)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 6 MCE banks
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping 0a
CPU0 attaching NULL sched-domain.
Switched to high resolution mode on CPU 1
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
CPU1 is up
ACPI: Waking up from system sleep state S3
pcieport-driver 0000:00:01.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
uhci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
uhci_hcd 0000:00:1a.1: power state changed by ACPI to D0
uhci_hcd 0000:00:1a.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900106, writing 0x2900102)
ehci_hcd 0000:00:1a.7: PME# disabled
HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100106, writing 0x100102)
pcieport-driver 0000:00:1c.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x7 (was 0x4040, writing 0x20004040)
pcieport-driver 0000:00:1c.1: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
pcieport-driver 0000:00:1c.2: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
pcieport-driver 0000:00:1c.3: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
pcieport-driver 0000:00:1c.4: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was 0x2800005, writing 0x2800001)
ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900106, writing 0x2900102)
ehci_hcd 0000:00:1d.7: PME# disabled
pci 0000:00:1e.0: restoring config space at offset 0x1 (was 0x100005, writing 0x100007)
ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00007, writing 0x2b00407)
nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x10, writing 0x0)
nvidia 0000:01:00.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100007)
ohci1394 0000:15:00.1: restoring config space at offset 0x3 (was 0x800000, writing 0x802000)
ohci1394 0000:15:00.1: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100006)
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: setting latency timer to 64
e1000e 0000:00:19.0: wake-up capability disabled by ACPI
e1000e 0000:00:19.0: PME# disabled
e1000e 0000:00:19.0: wake-up capability disabled by ACPI
e1000e 0000:00:19.0: PME# disabled
e1000e 0000:00:19.0: irq 31 for MSI/MSI-X
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1a.0: setting latency timer to 64
usb usb3: root hub lost power or was reset
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
usb usb4: root hub lost power or was reset
ehci_hcd 0000:00:1a.7: PME# disabled
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:1a.7: setting latency timer to 64
HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
HDA Intel 0000:00:1b.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
usb usb5: root hub lost power or was reset
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
usb usb6: root hub lost power or was reset
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
usb usb7: root hub lost power or was reset
ehci_hcd 0000:00:1d.7: PME# disabled
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:1d.7: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
PIIX_IDE 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
PIIX_IDE 0000:00:1f.1: setting latency timer to 64
ahci 0000:00:1f.2: setting latency timer to 64
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t4
ata1: irq_stat 0x00400040, connection status changed
ata1: hard resetting link
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
0000:00:19.0: eth0: 10/100 speed: disabling TSO
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
ath5k 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[f8101000-f81017ff] Max Packet=[2048] IR/IT contexts=[4/4]
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
thinkpad_acpi: ACPI backlight control delay disabled
sd 0:0:0:0: [sda] Starting disk
Restarting tasks ... done.
|
Last edited by johnny99 on Sat Apr 03, 2010 5:32 pm; edited 1 time in total |
|
| Back to top |
|
 |
Rexilion
Veteran
Joined: 17 Mar 2009
Posts: 1044
|
| Posted: Sat Apr 03, 2010 5:10 pm Post subject: |
|
|
| If you use pm-utils, you can use scripts to do that. Are you using that? |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
