| View previous topic :: View next topic |
| Author |
Message |
Johnny_Bit
Apprentice
Joined: 30 Aug 2005
Posts: 246
Location: Poland
|
 Posted: Fri May 07, 2010 11:04 pm Post subject: OpenGL za nic nie da sie ustawic bez vblank |
 |
|
Problem taki: na moim lapie z procesorem dual-core i kartą grafiki próbowałem uruchomić Unreal Tournament (ten stary), niestety ponieważ chodził tak 10x za szybko a sensownej rady jak to naprawić nie było, więc odintalowałem i gram na stacjonarnym. Ale, od tamtej pory wszystkie aplikacje opengl działają bardzo dziwnie: obraz skacze jak szalony, tzn za nic nie jest płynny raz jest bardzo szybki raz bardzo wolny.
glxgears daje:
| Code: | glxgears
Running synchronized to the vertical refresh. The framerate should be
approximately 1/1936613746 the monitor refresh rate.
311 frames in 5.0 seconds = 62.047 FPS
290 frames in 5.0 seconds = 57.827 FPS
304 frames in 5.0 seconds = 60.627 FPS
|
próbowałem ustawić w /etc/drirc:
| Code: | <driconf>
<device screen="0" driver="i915">
<application name="all">
<option name="vblank_mode" value="0" />
</application>
<application name="default">
<option name="vblank_mode" value="0" />
</application>
<application name="Default">
<option name="vblank_mode" value="0" />
</application>
<application name="glxgears">
<option name="vblank_mode" value="0" />
</application>
</device>
</driconf> |
ale to absolutnie nic nie daje, nadal jest taki dziwny vblank.
dodatkowo każda aplikacja fullscreen opengl po około 15~20 minutach chodzenia kompletnie zawiesza X-y i system: w logach później zamiast message od crona co 10 minut jest co 30 minut "---MARK---" w syslog i tyle się dzieje, system trzeba twardo resetować.
czy jest coś co mogę zmienić żeby znów działało dobrze? może jakieś podpowiedzi? |
|
| Back to top |
|
 |
dziadu
Guru
Joined: 04 May 2006
Posts: 467
Location: Kraków/Darmstadt/Munich
|
| Posted: Fri May 07, 2010 11:55 pm Post subject: |
|
|
A jesteś pewien, że działasz na sprzętowym OpenGL? Może przestawiło się na software'owy? Sprawdź co pokaże
| Code: | | eselect opengl list |
|
|
| Back to top |
|
|
Garrappachc
Guru
Joined: 26 Dec 2008
Posts: 362
Location: Kraków
|
| Posted: Sat May 08, 2010 6:08 am Post subject: |
|
|
I
| Code: | | glxinfo | grep OpenGL |
_________________
De profundis clamavi ad Te, Domine
emerge --info | virtual aviation |
|
| Back to top |
|
|
Johnny_Bit
Apprentice
Joined: 30 Aug 2005
Posts: 246
Location: Poland
|
| Posted: Sat May 08, 2010 8:04 pm Post subject: |
|
|
| Code: | johnny@hell /usr/src $ eselect opengl list
Available OpenGL implementations:
[1] xorg-x11 *
johnny@hell /usr/src $ glxinfo | grep OpenGL
OpenGL vendor string: Tungsten Graphics, Inc
OpenGL renderer string: Mesa DRI Intel(R) 945GM GEM 20100328 2010Q1 x86/MMX/SSE2
OpenGL version string: 1.4 Mesa 7.8.1
OpenGL extensions: |
Tak więc wszystko niby OK. ale nadal jest źle. włączenie screensavera na opengl to tragedia |
|
| Back to top |
|
|
dziadu
Guru
Joined: 04 May 2006
Posts: 467
Location: Kraków/Darmstadt/Munich
|
| Posted: Sat May 08, 2010 9:06 pm Post subject: |
|
|
Ja się na intelu nie znam, rozumiem, że Intel korzysta ze sterowników xorg-x11...
W takim razie pokaż jeszcze zawartość /var/log/Xorg.0.log |
|
| Back to top |
|
|
Johnny_Bit
Apprentice
Joined: 30 Aug 2005
Posts: 246
Location: Poland
|
| Posted: Sun May 09, 2010 12:00 am Post subject: |
|
|
OK... | Code: | hell src # cat /var/log/Xorg.0.log
[ 35.604]
X.Org X Server 1.8.0
Release Date: 2010-04-02
[ 35.604] X Protocol Version 11, Revision 0
[ 35.604] Build Operating System: Linux 2.6.33-gentoo-r1 i686 Gentoo
[ 35.604] Current Operating System: Linux hell 2.6.33-gentoo-r1 #1 SMP Mon Apr 12 23:21:49 CEST 2010 i686
[ 35.604] Kernel command line: root=/dev/sda2 quiet CONSOLE=/dev/tty1
[ 35.605] Build Date: 22 April 2010 09:08:31AM
[ 35.605]
[ 35.605] Current version of pixman: 0.18.0
[ 35.605] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 35.605] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 35.605] (==) Log file: "/var/log/Xorg.0.log", Time: Sat May 8 21:14:31 2010
[ 35.605] (==) Using config file: "/etc/X11/xorg.conf"
[ 35.605] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 35.635] (==) ServerLayout "X.org Configured"
[ 35.635] (**) |-->Screen "Screen0" (0)
[ 35.635] (**) | |-->Monitor "Monitor0"
[ 35.635] (**) | |-->Device "Card0"
[ 35.635] (**) Option "AllowEmptyInput" "true"
[ 35.635] (==) Automatically adding devices
[ 35.635] (==) Automatically enabling devices
[ 35.777] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/default/".
[ 35.777] Entry deleted from font path.
[ 35.777] (Run 'mkfontdir' on "/usr/share/fonts/default/").
[ 35.807] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/encodings/".
[ 35.807] Entry deleted from font path.
[ 35.807] (Run 'mkfontdir' on "/usr/share/fonts/encodings/").
[ 35.981] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/TTF/".
[ 35.981] Entry deleted from font path.
[ 35.981] (Run 'mkfontdir' on "/usr/share/fonts/TTF/").
[ 35.993] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/util/".
[ 35.994] Entry deleted from font path.
[ 35.994] (Run 'mkfontdir' on "/usr/share/fonts/util/").
[ 35.994] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/TTF/".
[ 35.994] Entry deleted from font path.
[ 35.994] (Run 'mkfontdir' on "/usr/share/fonts/TTF/").
[ 35.994] (**) FontPath set to:
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/,
/usr/share/fonts/corefonts/,
/usr/share/fonts/cyrillic/,
/usr/share/fonts/freefonts/,
/usr/share/fonts/inconsolata/,
/usr/share/fonts/misc/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Speedo/,
/usr/share/fonts/terminus/,
/usr/share/fonts/ttf-bitstream-vera/,
/usr/share/fonts/Type1/,
/usr/share/fonts/misc/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 35.994] (**) ModulePath set to "/usr/lib/xorg/modules"
[ 35.994] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 35.994] (II) Loader magic: 0x81df940
[ 35.994] (II) Module ABI versions:
[ 35.994] X.Org ANSI C Emulation: 0.4
[ 35.994] X.Org Video Driver: 7.0
[ 35.994] X.Org XInput driver : 9.0
[ 35.994] X.Org Server Extension : 3.0
[ 36.248] (--) PCI:*(0:0:2:0) 8086:27a2:1028:01d4 Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xeff00000/524288, 0xd0000000/268435456, 0xefec0000/262144, I/O @ 0x0000eff8/8
[ 36.248] (--) PCI: (0:0:2:1) 8086:27a6:1028:01d4 Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xeff80000/524288
[ 36.248] (II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
[ 36.248] (II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
[ 36.248] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 36.248] (II) "record" will be loaded. This was enabled by default and also specified in the config file.
[ 36.249] (II) "dri" will be loaded. This was enabled by default and also specified in the config file.
[ 36.249] (II) "dri2" will be loaded by default.
[ 36.249] (II) LoadModule: "glx"
[ 36.645] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 36.677] (II) Module glx: vendor="X.Org Foundation"
[ 36.677] compiled for 1.8.0, module version = 1.0.0
[ 36.677] ABI class: X.Org Server Extension, version 3.0
[ 36.679] (==) AIGLX enabled
[ 36.679] (II) Loading extension GLX
[ 36.679] (II) LoadModule: "extmod"
[ 36.689] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 36.713] (II) Module extmod: vendor="X.Org Foundation"
[ 36.713] compiled for 1.8.0, module version = 1.0.0
[ 36.713] Module class: X.Org Server Extension
[ 36.713] ABI class: X.Org Server Extension, version 3.0
[ 36.714] (II) Loading extension MIT-SCREEN-SAVER
[ 36.714] (II) Loading extension XFree86-VidModeExtension
[ 36.714] (II) Loading extension XFree86-DGA
[ 36.714] (II) Loading extension DPMS
[ 36.714] (II) Loading extension XVideo
[ 36.714] (II) Loading extension XVideo-MotionCompensation
[ 36.714] (II) Loading extension X-Resource
[ 36.714] (II) LoadModule: "record"
[ 36.714] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 36.715] (II) Module record: vendor="X.Org Foundation"
[ 36.715] compiled for 1.8.0, module version = 1.13.0
[ 36.715] Module class: X.Org Server Extension
[ 36.715] ABI class: X.Org Server Extension, version 3.0
[ 36.715] (II) Loading extension RECORD
[ 36.715] (II) LoadModule: "dbe"
[ 36.716] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 36.717] (II) Module dbe: vendor="X.Org Foundation"
[ 36.717] compiled for 1.8.0, module version = 1.0.0
[ 36.717] Module class: X.Org Server Extension
[ 36.717] ABI class: X.Org Server Extension, version 3.0
[ 36.717] (II) Loading extension DOUBLE-BUFFER
[ 36.717] (II) LoadModule: "dri"
[ 36.717] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 36.781] (II) Module dri: vendor="X.Org Foundation"
[ 36.781] compiled for 1.8.0, module version = 1.0.0
[ 36.781] ABI class: X.Org Server Extension, version 3.0
[ 36.781] (II) Loading extension XFree86-DRI
[ 36.781] (II) LoadModule: "dri2"
[ 36.782] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 36.782] (II) Module dri2: vendor="X.Org Foundation"
[ 36.782] compiled for 1.8.0, module version = 1.2.0
[ 36.783] ABI class: X.Org Server Extension, version 3.0
[ 36.783] (II) Loading extension DRI2
[ 36.783] (II) LoadModule: "intel"
[ 36.783] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 36.852] (II) Module intel: vendor="X.Org Foundation"
[ 36.852] compiled for 1.8.0, module version = 2.11.0
[ 36.852] Module class: X.Org Video Driver
[ 36.852] ABI class: X.Org Video Driver, version 7.0
[ 36.852] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale
[ 36.854] (++) using VT number 7
[ 36.865] (II) Primary Device is: PCI 00@00:02:0
[ 36.866] drmOpenDevice: node name is /dev/dri/card0
[ 36.866] drmOpenDevice: open result is 8, (OK)
[ 36.900] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 36.900] drmOpenDevice: node name is /dev/dri/card0
[ 36.900] drmOpenDevice: open result is 8, (OK)
[ 36.900] drmOpenByBusid: drmOpenMinor returns 8
[ 36.900] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 36.900] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 36.900] (==) intel(0): RGB weight 888
[ 36.900] (==) intel(0): Default visual is TrueColor
[ 36.900] (**) intel(0): Option "Tiling" "True"
[ 36.901] (II) intel(0): Integrated Graphics Chipset: Intel(R) 945GM
[ 36.901] (--) intel(0): Chipset: "945GM"
[ 36.901] (==) intel(0): video overlay key set to 0x101fe
[ 37.074] (II) intel(0): Output VGA1 using monitor section Monitor0
[ 37.179] (II) intel(0): Output LVDS1 has no monitor section
[ 37.179] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
[ 37.210] (II) intel(0): Output DVI1 has no monitor section
[ 37.556] (II) intel(0): Output TV1 has no monitor section
[ 37.580] (II) intel(0): EDID for output VGA1
[ 37.683] (II) intel(0): EDID for output LVDS1
[ 37.683] (II) intel(0): Manufacturer: SEC Model: 4650 Serial#: 0
[ 37.684] (II) intel(0): Year: 2005 Week: 0
[ 37.684] (II) intel(0): EDID Version: 1.3
[ 37.684] (II) intel(0): Digital Display Input
[ 37.684] (II) intel(0): Max Image Size [cm]: horiz.: 30 vert.: 23
[ 37.684] (II) intel(0): Gamma: 2.20
[ 37.684] (II) intel(0): No DPMS capabilities specified
[ 37.684] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 37.684] (II) intel(0): First detailed timing is preferred mode
[ 37.684] (II) intel(0): redX: 0.580 redY: 0.340 greenX: 0.310 greenY: 0.550
[ 37.684] (II) intel(0): blueX: 0.155 blueY: 0.155 whiteX: 0.313 whiteY: 0.329
[ 37.684] (II) intel(0): Manufacturer's mask: 0
[ 37.684] (II) intel(0): Supported detailed timing:
[ 37.684] (II) intel(0): clock: 108.0 MHz Image Size: 304 x 228 mm
[ 37.684] (II) intel(0): h_active: 1400 h_sync: 1448 h_sync_end 1560 h_blank_end 1688 h_border: 0
[ 37.684] (II) intel(0): v_active: 1050 v_sync: 1051 v_sync_end 1055 v_blanking: 1066 v_border: 0
[ 37.684] (II) intel(0): Unknown vendor-specific block f
[ 37.684] (II) intel(0): HG294
[ 37.684] (II) intel(0): �����hP
[ 37.684] (II) intel(0): EDID (in hex):
[ 37.684] (II) intel(0): 00ffffffffffff004ca3504600000000
[ 37.684] (II) intel(0): 000f0103801e17780a87f594574f8c27
[ 37.684] (II) intel(0): 27505400000001010101010101010101
[ 37.684] (II) intel(0): 010101010101302a7820511a10403070
[ 37.684] (II) intel(0): 140030e4100000190000000f00000000
[ 37.684] (II) intel(0): 00000000000ff2024b00000000fe0048
[ 37.685] (II) intel(0): 473239340031353050460a20000000fe
[ 37.685] (II) intel(0): 00e8d8d0c0a0685000020a2020200064
[ 37.685] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 37.685] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 37.685] (II) intel(0): Printing probed modes for output LVDS1
[ 37.685] (II) intel(0): Modeline "1400x1050"x60.0 108.00 1400 1448 1560 1688 1050 1051 1055 1066 -hsync -vsync (64.0 kHz)
[ 37.685] (II) intel(0): Modeline "1400x1050"x60.0 122.00 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync (64.9 kHz)
[ 37.685] (II) intel(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 37.685] (II) intel(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 37.686] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 37.686] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 37.686] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 37.686] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 37.715] (II) intel(0): EDID for output DVI1
[ 38.057] (II) intel(0): EDID for output TV1
[ 38.057] (II) intel(0): Output VGA1 disconnected
[ 38.057] (II) intel(0): Output LVDS1 connected
[ 38.057] (II) intel(0): Output DVI1 disconnected
[ 38.057] (II) intel(0): Output TV1 disconnected
[ 38.057] (II) intel(0): Using exact sizes for initial modes
[ 38.057] (II) intel(0): Output LVDS1 using initial mode 1400x1050
[ 38.057] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 38.057] (II) intel(0): Kernel page flipping support detected, enabling
[ 38.057] (==) intel(0): DPI set to (96, 96)
[ 38.057] (II) Loading sub module "fb"
[ 38.057] (II) LoadModule: "fb"
[ 38.058] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 38.075] (II) Module fb: vendor="X.Org Foundation"
[ 38.075] compiled for 1.8.0, module version = 1.0.0
[ 38.075] ABI class: X.Org ANSI C Emulation, version 0.4
[ 38.075] (==) Depth 24 pixmap format is 32 bpp
[ 38.075] (II) intel(0): [DRI2] Setup complete
[ 38.075] (II) intel(0): [DRI2] DRI driver: i915
[ 38.075] (**) intel(0): Tiling enabled
[ 38.075] (**) intel(0): SwapBuffers wait enabled
[ 38.075] (==) intel(0): VideoRam: 262144 KB
[ 38.075] (II) intel(0): Attempting memory allocation with tiled buffers.
[ 38.075] (II) intel(0): Tiled allocation successful.
[ 38.094] (II) UXA(0): Driver registered support for the following operations:
[ 38.094] (II) solid
[ 38.094] (II) copy
[ 38.094] (II) composite (RENDER acceleration)
[ 38.095] (II) put_image
[ 38.103] (==) intel(0): Backing store disabled
[ 38.103] (==) intel(0): Silken mouse enabled
[ 38.103] (II) intel(0): Initializing HW Cursor
[ 38.152] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 38.165] (==) intel(0): DPMS enabled
[ 38.165] (==) intel(0): Intel XvMC decoder disabled
[ 38.165] (II) intel(0): Set up textured video
[ 38.165] (II) intel(0): Set up overlay video
[ 38.165] (II) intel(0): direct rendering: DRI2 Enabled
[ 38.165] (WW) intel(0): Option "AccelMethod" is not used
[ 38.165] (--) RandR disabled
[ 38.165] (II) Initializing built-in extension Generic Event Extension
[ 38.165] (II) Initializing built-in extension SHAPE
[ 38.165] (II) Initializing built-in extension MIT-SHM
[ 38.165] (II) Initializing built-in extension XInputExtension
[ 38.165] (II) Initializing built-in extension XTEST
[ 38.165] (II) Initializing built-in extension BIG-REQUESTS
[ 38.165] (II) Initializing built-in extension SYNC
[ 38.165] (II) Initializing built-in extension XKEYBOARD
[ 38.165] (II) Initializing built-in extension XC-MISC
[ 38.165] (II) Initializing built-in extension XINERAMA
[ 38.165] (II) Initializing built-in extension XFIXES
[ 38.165] (II) Initializing built-in extension RENDER
[ 38.166] (II) Initializing built-in extension RANDR
[ 38.166] (II) Initializing built-in extension COMPOSITE
[ 38.166] (II) Initializing built-in extension DAMAGE
[ 38.296] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 38.296] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 38.296] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 38.296] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 38.296] (II) AIGLX: Loaded and initialized /usr/lib/dri/i915_dri.so
[ 38.296] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 38.297] (II) intel(0): Setting screen physical size to 370 x 277
[ 39.518] (II) config/udev: Adding input device Video Bus (/dev/input/event3)
[ 39.518] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 39.518] (**) Video Bus: Applying InputClass "Keyboard Defaults"
[ 39.518] (II) LoadModule: "evdev"
[ 39.518] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 39.537] (II) Module evdev: vendor="X.Org Foundation"
[ 39.537] compiled for 1.8.0, module version = 2.4.0
[ 39.537] Module class: X.Org XInput Driver
[ 39.537] ABI class: X.Org XInput driver, version 9.0
[ 39.538] (**) Video Bus: always reports core events
[ 39.538] (**) Video Bus: Device: "/dev/input/event3"
[ 39.540] (II) Video Bus: Found keys
[ 39.540] (II) Video Bus: Configuring as keyboard
[ 39.540] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
[ 39.540] (**) Option "xkb_rules" "evdev"
[ 39.540] (**) Option "xkb_model" "pc105"
[ 39.540] (**) Option "xkb_layout" "pl"
[ 39.652] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 39.652] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 39.652] (**) Power Button: Applying InputClass "Keyboard Defaults"
[ 39.652] (**) Power Button: always reports core events
[ 39.652] (**) Power Button: Device: "/dev/input/event1"
[ 39.656] (II) Power Button: Found keys
[ 39.656] (II) Power Button: Configuring as keyboard
[ 39.656] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 39.656] (**) Option "xkb_rules" "evdev"
[ 39.656] (**) Option "xkb_model" "pc105"
[ 39.656] (**) Option "xkb_layout" "pl"
[ 39.657] (II) config/udev: Adding input device Lid Switch (/dev/input/event0)
[ 39.657] (EE) No input driver/identifier specified (ignoring)
[ 39.658] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 39.658] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 39.658] (**) Sleep Button: Applying InputClass "Keyboard Defaults"
[ 39.658] (**) Sleep Button: always reports core events
[ 39.658] (**) Sleep Button: Device: "/dev/input/event2"
[ 39.661] (II) Sleep Button: Found keys
[ 39.661] (II) Sleep Button: Configuring as keyboard
[ 39.661] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
[ 39.661] (**) Option "xkb_rules" "evdev"
[ 39.661] (**) Option "xkb_model" "pc105"
[ 39.661] (**) Option "xkb_layout" "pl"
[ 39.674] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event4)
[ 39.674] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 39.674] (**) AT Translated Set 2 keyboard: Applying InputClass "Keyboard Defaults"
[ 39.674] (**) AT Translated Set 2 keyboard: always reports core events
[ 39.674] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event4"
[ 39.678] (II) AT Translated Set 2 keyboard: Found keys
[ 39.678] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[ 39.678] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
[ 39.678] (**) Option "xkb_rules" "evdev"
[ 39.678] (**) Option "xkb_model" "pc105"
[ 39.678] (**) Option "xkb_layout" "pl"
[ 39.679] (II) config/udev: Adding input device PS/2 Mouse (/dev/input/event5)
[ 39.679] (**) PS/2 Mouse: Applying InputClass "evdev pointer catchall"
[ 39.679] (**) PS/2 Mouse: always reports core events
[ 39.679] (**) PS/2 Mouse: Device: "/dev/input/event5"
[ 39.682] (II) PS/2 Mouse: Found 3 mouse buttons
[ 39.682] (II) PS/2 Mouse: Found relative axes
[ 39.682] (II) PS/2 Mouse: Found x and y relative axes
[ 39.682] (II) PS/2 Mouse: Configuring as mouse
[ 39.682] (**) PS/2 Mouse: YAxisMapping: buttons 4 and 5
[ 39.682] (**) PS/2 Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 39.682] (II) XINPUT: Adding extended input device "PS/2 Mouse" (type: MOUSE)
[ 39.682] (**) PS/2 Mouse: (accel) keeping acceleration scheme 1
[ 39.682] (**) PS/2 Mouse: (accel) acceleration profile 0
[ 39.682] (**) PS/2 Mouse: (accel) acceleration factor: 2.000
[ 39.682] (**) PS/2 Mouse: (accel) acceleration threshold: 4
[ 39.682] (II) PS/2 Mouse: initialized for relative axes.
[ 39.683] (II) config/udev: Adding input device PS/2 Mouse (/dev/input/mouse0)
[ 39.683] (EE) No input driver/identifier specified (ignoring)
[ 39.683] (II) config/udev: Adding input device AlpsPS/2 ALPS GlidePoint (/dev/input/event6)
[ 39.683] (**) AlpsPS/2 ALPS GlidePoint: Applying InputClass "evdev touchpad catchall"
[ 39.683] (**) AlpsPS/2 ALPS GlidePoint: Applying InputClass "touchpad catchall"
[ 39.683] (II) LoadModule: "synaptics"
[ 39.683] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 39.706] (II) Module synaptics: vendor="X.Org Foundation"
[ 39.706] compiled for 1.8.0, module version = 1.2.2
[ 39.706] Module class: X.Org XInput Driver
[ 39.706] ABI class: X.Org XInput driver, version 9.0
[ 39.706] (II) Synaptics touchpad driver version 1.2.2
[ 39.706] (**) Option "Device" "/dev/input/event6"
[ 39.716] (II) AlpsPS/2 ALPS GlidePoint: x-axis range 0 - 1023
[ 39.716] (II) AlpsPS/2 ALPS GlidePoint: y-axis range 0 - 767
[ 39.716] (II) AlpsPS/2 ALPS GlidePoint: pressure range 0 - 127
[ 39.716] (II) AlpsPS/2 ALPS GlidePoint: finger width range 0 - 0
[ 39.716] (II) AlpsPS/2 ALPS GlidePoint: buttons: left right middle
[ 39.716] (**) Option "LeftEdge" "130"
[ 39.716] (**) Option "RightEdge" "840"
[ 39.716] (**) Option "TopEdge" "130"
[ 39.716] (**) Option "BottomEdge" "640"
[ 39.716] (**) Option "FingerLow" "7"
[ 39.716] (**) Option "FingerHigh" "8"
[ 39.717] (**) Option "MaxTapTime" "180"
[ 39.717] (**) Option "ClickTime" "0"
[ 39.717] (**) Option "EmulateMidButtonTime" "75"
[ 39.717] (**) Option "VertScrollDelta" "20"
[ 39.717] (**) Option "HorizScrollDelta" "20"
[ 39.717] (**) Option "VertEdgeScroll" "true"
[ 39.717] (**) Option "EdgeMotionMinSpeed" "200"
[ 39.717] (**) Option "EdgeMotionMaxSpeed" "200"
[ 39.717] (**) Option "UpDownScrolling" "1"
[ 39.717] (**) Option "RTCornerButton" "2"
[ 39.717] (**) Option "TapButton1" "1"
[ 39.717] (**) Option "CircularScrolling" "1"
[ 39.717] (**) Option "CircScrollTrigger" "3"
[ 39.718] (**) Option "MinSpeed" "0.40"
[ 39.718] (**) Option "MaxSpeed" "0.65"
[ 39.718] (**) Option "AccelFactor" "0.030"
[ 39.718] (**) Option "CircScrollDelta" "0.1"
[ 39.726] (--) AlpsPS/2 ALPS GlidePoint: touchpad found
[ 39.726] (**) AlpsPS/2 ALPS GlidePoint: always reports core events
[ 39.730] (II) XINPUT: Adding extended input device "AlpsPS/2 ALPS GlidePoint" (type: TOUCHPAD)
[ 39.730] (**) AlpsPS/2 ALPS GlidePoint: (accel) keeping acceleration scheme 1
[ 39.730] (**) AlpsPS/2 ALPS GlidePoint: (accel) acceleration profile 0
[ 39.730] (**) AlpsPS/2 ALPS GlidePoint: (accel) acceleration factor: 2.000
[ 39.730] (**) AlpsPS/2 ALPS GlidePoint: (accel) acceleration threshold: 4
[ 39.738] (--) AlpsPS/2 ALPS GlidePoint: touchpad found
[ 39.738] (II) config/udev: Adding input device AlpsPS/2 ALPS GlidePoint (/dev/input/mouse1)
[ 39.738] (EE) No input driver/identifier specified (ignoring)
[ 70.046] (II) intel(0): EDID vendor "SEC", prod id 18000
[ 70.046] (II) intel(0): Printing DDC gathered Modelines:
[ 70.046] (II) intel(0): Modeline "1400x1050"x0.0 108.00 1400 1448 1560 1688 1050 1051 1055 1066 -hsync -vsync (64.0 kHz)
[ 70.549] (II) intel(0): EDID vendor "SEC", prod id 18000
[ 70.549] (II) intel(0): Printing DDC gathered Modelines:
[ 70.549] (II) intel(0): Modeline "1400x1050"x0.0 108.00 1400 1448 1560 1688 1050 1051 1055 1066 -hsync -vsync (64.0 kHz)
[ 74.292] (II) intel(0): EDID vendor "SEC", prod id 18000
[ 74.292] (II) intel(0): Printing DDC gathered Modelines:
[ 74.292] (II) intel(0): Modeline "1400x1050"x0.0 108.00 1400 1448 1560 1688 1050 1051 1055 1066 -hsync -vsync (64.0 kHz) |
Ja tam nic ciekawego nie widzę... |
|
| Back to top |
|
|
Johnny_Bit
Apprentice
Joined: 30 Aug 2005
Posts: 246
Location: Poland
|
| Posted: Sun May 09, 2010 1:39 am Post subject: |
|
|
jest jednak coś ciekawego: przeglądałem zdjęcia z aparatu o dużej rozdzielczości i w pewnym momencie jedno zdjęcie zrobiło się takie "pochlastane" a przy próbie zbliżenia całe czarne, gdy chciałem wyjść z gqview nic nie działało oprócz myszki którą mogłem ruszać i ewentualnie przełączyć się na konsole systemową. w logach było to: | Code: | May 9 03:17:52 hell kernel: [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung
May 9 03:17:52 hell kernel: render error detected, EIR: 0x00000000
May 9 03:17:52 hell kernel: [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 1281159 at 1281156)
May 9 03:17:52 hell kernel: ------------[ cut here ]------------
May 9 03:17:52 hell kernel: WARNING: at drivers/gpu/drm/i915/i915_gem_tiling.c:490 i915_gem_set_tiling+0x15b/0x1ac()
May 9 03:17:52 hell kernel: Hardware name: Latitude D520
May 9 03:17:52 hell kernel: failed to reset object for tiling switch
May 9 03:17:52 hell kernel: Modules linked in: snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_hwdep iwl3945
May 9 03:17:52 hell kernel: Pid: 5343, comm: X Not tainted 2.6.33-gentoo-r1 #1
May 9 03:17:52 hell kernel: Call Trace:
May 9 03:17:52 hell kernel: [<c1027e66>] ? warn_slowpath_common+0x5e/0x8a
May 9 03:17:52 hell kernel: [<c1027ec4>] ? warn_slowpath_fmt+0x26/0x2a
May 9 03:17:52 hell kernel: [<c1253294>] ? i915_gem_set_tiling+0x15b/0x1ac
May 9 03:17:52 hell kernel: [<c123bc19>] ? drm_ioctl+0x213/0x2a4
May 9 03:17:52 hell kernel: [<c1253139>] ? i915_gem_set_tiling+0x0/0x1ac
May 9 03:17:52 hell kernel: [<c100873e>] ? restore_i387_fxsave+0x5c/0x6d
May 9 03:17:52 hell kernel: [<c123ba06>] ? drm_ioctl+0x0/0x2a4
May 9 03:17:52 hell kernel: [<c1087945>] ? vfs_ioctl+0x1c/0x7d
May 9 03:17:52 hell kernel: [<c1087ed2>] ? do_vfs_ioctl+0x485/0x4c0
May 9 03:17:52 hell kernel: [<c107df92>] ? vfs_read+0xf1/0x102
May 9 03:17:52 hell kernel: [<c1002366>] ? restore_sigcontext+0xba/0xd1
May 9 03:17:52 hell kernel: [<c1087f4e>] ? sys_ioctl+0x41/0x58
May 9 03:17:52 hell kernel: [<c1002710>] ? sysenter_do_call+0x12/0x26
May 9 03:17:52 hell kernel: ---[ end trace 4c3c1199ee426b3d ]---
May 9 03:19:30 hell login[5377]: pam_unix(login:session): session opened for user root by LOGIN(uid=0)
May 9 03:19:30 hell login[15920]: ROOT LOGIN on 'tty1' |
zabiłem Xy itd, ale później nie dało się za nic ich włączyć, potrzebny był pełny reboot |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Polskie forum (Polish)
