| View previous topic :: View next topic |
| Author |
Message |
Epyon
l33t
Joined: 11 Sep 2003
Posts: 754
Location: NJ, USA
|
 Posted: Thu Sep 11, 2003 2:20 am Post subject: D-Link DFE-530TX problem |
 |
|
During the install of gentoo 1.4, my NIC worked fine. I could get online and download everything that I needed. Now though after the install, I can't even ping my router. If I ping anything other than my computer I get a destination host unreachable error.
This is the output of ifconfig:
| Quote: |
eth0 Link encap:Ethernet HWaddr 00:50:BA:B3:3D:9E
inet addr:192.168.10.154 Bcast:192.168.10.255 Mask:255.255.255.0
inet6 addr: fe80::250:baff:feb3:3d9e/10 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0xe000
|
My IP, broadcast, and subnet mask are set correctly. I set the gateway to my router in /etc/config.d/net. The output of route seems correct. There is something strange in the dmesg output though.
| Quote: | via-rhine.c:v1.10-LK1.1.14 May-3-2002 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT86C100A Rhine at 0xe000, 00:50:ba:b3:3d:9e, IRQ 10.
eth0: MII PHY found at address 8, status 0x782d advertising 05e1 Link 45e1.
eth0: Setting full-duplex based on MII #8 link partner capability of 45e1.
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting...
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 782d, resetting.. |
Does anyone know how to fix this? |
|
| Back to top |
|
 |
bombcar
Guru
Joined: 08 Apr 2003
Posts: 453
Location: Wisconsin
|
| Posted: Thu Sep 11, 2003 2:32 am Post subject: You could try |
|
|
disabling ipv6 and rebooting; or try to force the network card into half-duplex mode.
Also, try to compare the output of ifconfig, route -n, and dmesg between the Live CD and the system boot. |
|
| Back to top |
|
|
Epyon
l33t
Joined: 11 Sep 2003
Posts: 754
Location: NJ, USA
|
| Posted: Thu Sep 11, 2003 2:39 am Post subject: |
|
|
| Fixed it. Had to use pci=noacpi. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
