| View previous topic :: View next topic |
| Author |
Message |
wertthelert
n00b
Joined: 17 Jun 2010
Posts: 4
|
 Posted: Fri Jun 18, 2010 1:13 am Post subject: computer crash |
 |
|
hello. when i have install this software it computer, make crash. how can i fix the error???  |
|
| Back to top |
|
 |
Muso
Veteran
Joined: 22 Oct 2002
Posts: 1052
Location: The Holy city of Honolulu
|
| Posted: Fri Jun 18, 2010 1:44 am Post subject: |
|
|
What? Can you be a bit more specific?
(unless this is a test post by a spambot)
_________________
"You can lead a horticulture but you can't make her think" ~ Dorothy Parker
2021 is the year of the Linux Desktop! |
|
| Back to top |
|
|
cach0rr0
Bodhisattva
Joined: 13 Nov 2008
Posts: 4123
Location: Houston, Republic of Texas
|
|
| Back to top |
|
|
wertthelert
n00b
Joined: 17 Jun 2010
Posts: 4
|
| Posted: Fri Jun 18, 2010 2:40 am Post subject: |
|
|
i have installed the ubuntu on our computer. now when the operating system initialize there is only one message. it is displaying NO SIGNAL INPUT. then the power is lost. please help  |
|
| Back to top |
|
|
Hu
Administrator
Joined: 06 Mar 2007
Posts: 21722
|
| Posted: Fri Jun 18, 2010 3:05 am Post subject: |
|
|
| wertthelert: I think you are a bit lost. This is a Gentoo Linux forum, not an Ubuntu Linux forum. Although we can provide help that is general in nature, system specific troubleshooting would be better done via the Ubuntu forums. That said, your problem is that you are not getting a video signal, which is likely a much more basic problem. Do you see the POST messages when the computer first powers on? Did you configure Ubuntu to boot to text mode, to a framebuffer console, or straight to graphics mode? Does the signal come back if you switch to a text console? |
|
| Back to top |
|
|
wertthelert
n00b
Joined: 17 Jun 2010
Posts: 4
|
| Posted: Fri Jun 18, 2010 3:20 am Post subject: |
|
|
| i have already tried getting help but not succeeded. the only message appearing is NO SIGNAL INPUT. there is not the correct output for operating system initialization. we have tried booting from the CD-ROM. the same error happens. i have tried to initialize the windows operating system but have failure. we cannot utilize the computer for any purposes. |
|
| Back to top |
|
|
cach0rr0
Bodhisattva
Joined: 13 Nov 2008
Posts: 4123
Location: Houston, Republic of Texas
|
| Posted: Fri Jun 18, 2010 5:00 am Post subject: |
|
|
| wertthelert wrote: | | i have already tried getting help but not succeeded. the only message appearing is NO SIGNAL INPUT. there is not the correct output for operating system initialization. we have tried booting from the CD-ROM. the same error happens. i have tried to initialize the windows operating system but have failure. we cannot utilize the computer for any purposes. |
"NO SIGNAL INPUT" is normally seen when...well, when your monitor isn't actually hooked up to anything. When it isn't getting any signal, rather.
either your video card/output is bad, or, your monitor isn't hooked up
_________________
Lost configuring your system?
dump lspci -n here | see Pappy's guide | Link Stash |
|
| Back to top |
|
|
wertthelert
n00b
Joined: 17 Jun 2010
Posts: 4
|
| Posted: Sat Jun 19, 2010 8:10 pm Post subject: |
|
|
| after having configure the nvidia graphics accelerator. success is attained. we are grateful for your assistance. |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54317
Location: 56N 3W
|
| Posted: Mon Jun 21, 2010 4:03 pm Post subject: |
|
|
Moved from Installing Gentoo to Unsupported Software.
As its not a Gentoo issue
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
|
Unsupported Software
