| View previous topic :: View next topic |
| Author |
Message |
Trifaux666
Tux's lil' helper
Joined: 21 Sep 2003
Posts: 112
Location: Italia - Roma
|
 Posted: Sun Sep 21, 2003 12:26 pm Post subject: il kernel fa i capricci [risolto] |
 |
|
Già ceh devo ricompilare il kernel con i moduli del suono,
vorrei da voi tutti un parere su quello che mi succede:
ho ricompilato il kernel da poco (facendo per bene tutti i passaggi, e facendomi seguire e controllare da un amico) che comunque elencco qua:
| Code: | cd /usr/src/linux
rm .config
make menuconfig |
così dopo aver inserito tutto ciò che mi serve, ovviamente incluso devfs,
| Code: | make dep && make clean bzImage modules modules_install
cp /usr/src/linux/arch/i386/bzImage /boot |
abilitando il supporto delle partizioni VFAT, MSDOS FS e di conseguenza fat32, come built-in,
compilato tutto, ma... quando vado a fare | Code: | | mount /dev/hda1 /mnt/windows |
mi viene fuori la seguente: | Code: | | mount: fs type vfat not supported by kernel |
come mai, se ho compilato il supporto nel kernel? dove sbaglio?
e inoltre al boot mi viene fuori una scritta che dice che non ho compilato il supporto devfs che gentoo richiede... help!
Last edited by Trifaux666 on Sun Sep 21, 2003 2:50 pm; edited 1 time in total |
|
| Back to top |
|
 |
hellraiser
Guru
Joined: 14 Jun 2003
Posts: 431
Location: Pescara [Italy]
|
| Posted: Sun Sep 21, 2003 12:37 pm Post subject: |
|
|
che kernel hai preso ??
gentoo-sources ??
cmq se potrei postarci la parte di dmesg, cosi vediamo gli errori al boot...
per il vfat, prova a mettere il supporto modulare...e a caricare il modulo all avvio...
_________________
Io non sono nessuno...ma nessuno è come me!
"Open Source is a good idea..." |
|
| Back to top |
|
|
fedeliallalinea
Administrator
Joined: 08 Mar 2003
Posts: 30964
Location: here
|
| Posted: Sun Sep 21, 2003 12:40 pm Post subject: |
|
|
Quando hai fatto questo passaggio
| Code: | make dep && make clean bzImage modules modules_install
cp /usr/src/linux/arch/i386/bzImage /boot |
hai montato la cartella /boot (gentoo la smonta sempre una volta finito
di usarla).
| Trifaux666 wrote: | | e inoltre al boot mi viene fuori una scritta che dice che non ho compilato il supporto devfs che gentoo richiede... help! |
Per questo devi abilitare nel kernel il support che sta in
| Code: | File systems --->
[*] /dev file system support (EXPERIMENTAL)
[*] Automatically mount at boot
[ ] Debug devfs |
_________________
Questions are guaranteed in life; Answers aren't. |
|
| Back to top |
|
|
Trifaux666
Tux's lil' helper
Joined: 21 Sep 2003
Posts: 112
Location: Italia - Roma
|
| Posted: Sun Sep 21, 2003 12:45 pm Post subject: |
|
|
| hellraiser wrote: | | che kernel hai preso ?? gentoo-sources ?? |
si
| hellraiser wrote: | | cmq se potrei postarci la parte di dmesg, cosi vediamo gli errori al boot... |
eccolo.
| Code: | Linux version 2.4.20-gentoo-r6 (root@cdimage) (gcc version 3.2.3 20030422 (Gento
o Linux 1.4 3.2.3-r1, propolice)) #4 SMP Sun Sep 14 00:04:37 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ec000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000013ff0000 (usable)
BIOS-e820: 0000000013ff0000 - 0000000013ff8000 (ACPI data)
BIOS-e820: 0000000013ff8000 - 0000000014000000 (ACPI NVS)
BIOS-e820: 00000000ffee0000 - 00000000fff0ffff (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
319MB LOWMEM available.
On node 0 totalpages: 81904
zone(0): 4096 pages.
zone(1): 77808 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=gentoo ro root=302
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 399.017 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 794.62 BogoMIPS
Memory: 317624k/327616k available (1952k kernel code, 7428k reserved, -2432k dat
a, 136k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 730.21 usecs.
task migration cache decay timeout: 5 msecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 399.0125 MHz.
..... host bus clock speed is 66.2520 MHz.
cpu: 0, clocks: 332520, slice: 166260
CPU0<T0:332512,T1:166240,D:12,S:166260,C:332520>
migration_task 0 on cpu=0
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS [1039/0008] at 00:02.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
QNX4 filesystem 0.2.2 registered.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI IS
APNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller on PCI bus 00 dev 15
SIS5513: detected chipset, but driver not compiled in!
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y080L0, ATA DISK drive
hdb: ST320413A, ATA DISK drive
hdc: HITACHI DVD-ROM GD-7500, ATAPI CD/DVD-ROM drive
hdd: PHILIPS CDRW2010, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=9964/255/63
hdb: setmax LBA 39102337, native 39102336
hdb: 39102336 sectors (20020 MB) w/512KiB Cache, CHS=2434/255/63
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
hdd: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdb: hdb1 hdb2 hdb3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 00:0d.0
PCI: Sharing IRQ 11 with 00:02.7
eth0: RealTek RTL8139 Fast Ethernet at 0xd4800f00, 00:e0:7d:c8:b3:71, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 262M
agpgart: Unsupported SiS chipset (device id: 0635), you might want to try agp_tr
y_unsupported=1.
agpgart: no supported devices found.
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] Initialized radeon 1.1.1 20010405 on minor 1
[drm:drm_init] *ERROR* Cannot initialize the agpgart module.
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
es1371: version v0.30 time 00:14:52 Sep 14 2003
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
reiserfs: checking transaction log (device 03:02) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 136k freed
Adding Swap: 489940k swap-space (priority -1)
reiserfs: checking transaction log (device 03:06) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed. |
l'errore di devfs lo da in un'altra schermata, dice di premere un tasto per continuare o aspettare 15 secondi per fare il boot comunque. |
|
| Back to top |
|
|
Trifaux666
Tux's lil' helper
Joined: 21 Sep 2003
Posts: 112
Location: Italia - Roma
|
| Posted: Sun Sep 21, 2003 12:47 pm Post subject: |
|
|
| fedeliallalinea wrote: | hai montato la cartella /boot (gentoo la smonta sempre una volta finito
di usarla). |
si l'ho montata e poi prima di raivviare l'ho smontata io per sicurezza.
| fedeliallalinea wrote: | Per questo devi abilitare nel kernel il support che sta in
| Code: | File systems --->
[*] /dev file system support (EXPERIMENTAL)
[*] Automatically mount at boot
[ ] Debug devfs |
|
la cosa brutta è che io questo l'ho fatto. |
|
| Back to top |
|
|
JacoMozzi
l33t
Joined: 12 May 2003
Posts: 645
Location: Giubiasco world(EU(CH(TI)))
|
| Posted: Sun Sep 21, 2003 12:57 pm Post subject: |
|
|
Hai fatto partire lilo o grub per fargli sapere che hai cambiato immagine del kernel??
Ciao
Jaco |
|
| Back to top |
|
|
fedeliallalinea
Administrator
Joined: 08 Mar 2003
Posts: 30964
Location: here
|
| Posted: Sun Sep 21, 2003 12:57 pm Post subject: |
|
|
Mi sembra molto strano. Ricompila il kernel e mettilo in /boot
cambiando il nome (es: bzImage.new) e poi configura lilo o grub con
la possibilita' di scegliere i due kernel. Ti dico questo perche' se tu hai
aggiunto il supporto devfs e non te lo carica vuol dire che l'immagine
che si trova in boot e' ancora quella vecchia.
_________________
Questions are guaranteed in life; Answers aren't. |
|
| Back to top |
|
|
Trifaux666
Tux's lil' helper
Joined: 21 Sep 2003
Posts: 112
Location: Italia - Roma
|
| Posted: Sun Sep 21, 2003 12:59 pm Post subject: |
|
|
| capisco, ora ricompilo e vi faccio sapere. |
|
| Back to top |
|
|
paolo
l33t
Joined: 23 Jul 2002
Posts: 768
Location: SBT (AP)
|
| Posted: Sun Sep 21, 2003 1:42 pm Post subject: |
|
|
| Trifaux666 wrote: |
| Code: | Linux version 2.4.20-gentoo-r6 (root@cdimage) (gcc version 3.2.3 20030422 (Gento
o Linux 1.4 3.2.3-r1, propolice)) #4 SMP Sun Sep 14 00:04:37 CEST 2003
...
|
|
Da qui sembra che il kernel sia stato ricompilato il 14 mentre il thread è del 21...
_________________
Nihil sine magno labore |
|
| Back to top |
|
|
Trifaux666
Tux's lil' helper
Joined: 21 Sep 2003
Posts: 112
Location: Italia - Roma
|
| Posted: Sun Sep 21, 2003 2:56 pm Post subject: |
|
|
| paolo wrote: | | Da qui sembra che il kernel sia stato ricompilato il 14 mentre il thread è del 21... |
si lo avevo ricompilato in quella data ma non ho avuto tempo per rifarlo. Comuqnue ora ho risolto, funziona tutto quello che ho selezionato. Grazie a tutti per l'aiuto, non so come ho risolto, probabilmente avevo fatto qualche "vaccata" quando ho compilato quello vecchio, infatti col comando | Code: | bash-2.05b# umount /boot
bash-2.05b# cd /boot
bash-2.05b# ls
bzImage |
non so che ci facesse quella roba lì... comunque ho anche chiamato il kernel bzImage.new come mi avete suggerito voi e ho modificato il lilo. ora sembra che vada tutto a meraviglia. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Forum italiano (Italian)
