| View previous topic :: View next topic |
| Author |
Message |
paraw
Apprentice
Joined: 07 Jan 2005
Posts: 169
Location: Stara Zagora (BG)
|
 Posted: Sun Aug 08, 2010 3:42 am Post subject: O2 micro card reader |
 |
|
I've got this card reader in my Dell Studio 17 laptop, but I haven't been able to make it work yet. Relevant output of lspci:
| Code: | 14:00.1 SD Host controller [0805]: O2 Micro, Inc. Device [1217:8120] (rev 01)
14:00.2 Mass storage controller [0180]: O2 Micro, Inc. Device [1217:8130] (rev 01) |
The options I have selected in the kernel (2.6.34-r1 x86_64) are:
| Code: | MMC=y
MMC_BLOCK=y
MMC_BLOCK_BOUNCE=y
MMC_SDHCI=y
MMC_SDHCI_PCI=y
|
Everything else MMC not set.
When I insert a memory card in the reader nothing happens at all: nothing in dmesg, no new devices... nothing at all. Any idea what I'm doing wrong? |
|
| Back to top |
|
 |
USTruck
Guru
Joined: 21 Aug 2005
Posts: 423
Location: La Louviere (Belgique)
|
| Posted: Sun Aug 08, 2010 8:21 am Post subject: |
|
|
Hello,
I have Studio 17 too. I not complete settings of kernel, lot of options are under modules or not necessary, I not fully tested all hardware of.
My Kernel config
| Code: | #
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_HOTPLUG_PCI=y
-----------------
#
# MMC/SD/SDIO Card Drivers
#
CONFIG_MMC_BLOCK=m
CONFIG_MMC_BLOCK_BOUNCE=y
CONFIG_SDIO_UART=m
CONFIG_MMC_TEST=m
#
# MMC/SD/SDIO Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
CONFIG_MMC_SDHCI_PCI=m
CONFIG_MMC_RICOH_MMC=y
CONFIG_MMC_SDHCI_PLTFM=m
CONFIG_MMC_WBSD=m
CONFIG_MMC_TIFM_SD=m
CONFIG_MMC_CB710=m
CONFIG_MMC_VIA_SDMMC=m
CONFIG_MEMSTICK=y
# CONFIG_MEMSTICK_DEBUG is not set
#
# MemoryStick drivers
#
# CONFIG_MEMSTICK_UNSAFE_RESUME is not set
CONFIG_MSPRO_BLOCK=m
#
# MemoryStick Host Controller Drivers
#
CONFIG_MEMSTICK_TIFM_MS=m
CONFIG_MEMSTICK_JMICRON_38X=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
# CONFIG_RTC_DEBUG is not set
|
lspci | Code: | 14:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01)
14:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01)
14:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) |
lsmod | Code: | Module Size Used by
rfcomm 33680 0
l2cap 32076 3 rfcomm
firewire_ohci 22318 0
firewire_core 43109 1 firewire_ohci
ohci1394 27164 0
wl 1934188 0
sdhci_pci 6483 0
sdhci 14715 1 sdhci_pci
ieee1394 69534 1 ohci1394
|
|
|
| Back to top |
|
|
paraw
Apprentice
Joined: 07 Jan 2005
Posts: 169
Location: Stara Zagora (BG)
|
| Posted: Tue May 31, 2011 3:47 pm Post subject: |
|
|
So, after almost one full year, I'm still unable to get the card reader to work. The kernel config options are still the same, and still nothing happens when I insert a memory card in the slot.
Help...? |
|
| Back to top |
|
|
shiznix
Guru
Joined: 29 Jun 2003
Posts: 367
Location: Adelaide, Australia
|
| Posted: Thu Jun 16, 2011 11:29 am Post subject: |
|
|
| paraw wrote: | So, after almost one full year, I'm still unable to get the card reader to work. The kernel config options are still the same, and still nothing happens when I insert a memory card in the slot.
Help...? |
The O2 Micro SD/MMC Card Reader uses the the kernel's sdhci support.
An example configuration under my 2.6.35 kernel's menuconfig 'Device Drivers > MMC/SD/SDIO card support':
| Code: | [ ] MMC debugging
[ ] Assume MMC/SD cards are non-removable (DANGEROUS)
*** MMC/SD/SDIO Card Drivers ***
<*> MMC block device driver
[*] Use bounce buffer for simple hosts
< > SDIO UART/GPS class support
< > MMC host test driver
*** MMC/SD/SDIO Host Controller Drivers ***
<*> Secure Digital Host Controller Interface support
<*> SDHCI support on PCI bus
[ ] Ricoh MMC Controller Disabler (EXPERIMENTAL)
<*> SDHCI support on the platform specific bus
< > Winbond W83L51xD SD/MMC Card Interface support
< > TI Flash Media MMC/SD Interface support (EXPERIMENTAL)
< > MMC/SD driver for Ricoh Bay1Controllers (EXPERIMENTAL)
< > ENE CB710 MMC/SD Interface support
< > VIA SD/MMC Card Reader Driver |
My device: | Code: | 14:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) (prog-if 01)
Subsystem: Dell Device 041b
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at f0e03800 (32-bit, non-prefetchable) [size=256]
Capabilities: [a0] Power Management version 3
Capabilities: [48] MSI: Enable- Count=1/1 Maskable+ 64bit+
Capabilities: [80] Express Endpoint, MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [200] Advanced Error Reporting
Kernel driver in use: sdhci-pci |
Inserting an 8GB SD card into the slot exposes the following output in syslog: | Code: | kernel: [ 160.176423] mmc0: new SDHC card at address e624
kernel: [ 160.176616] mmcblk0: mmc0:e624 SU08G 7.40 GiB
kernel: [ 160.176680] mmcblk0: p1 |
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
