View previous topic :: View next topic |
Author |
Message |
Royal_ts n00b

Joined: 23 May 2011 Posts: 44 Location: Leipzig
|
Posted: Thu Mar 15, 2012 10:27 am Post subject: wpa_supplicant |
|
|
Hey guys!
I want to connect with wpa supplicant to my ap. It looks fine for me. the output of wpa_supplicant is:
Code: |
localhost royalts # wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -D wext -i wlan0 -d
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='0'
ap_scan=1
Priority group 3
id=1 ssid='AndroidAP5031'
Priority group 2
id=0 ssid='BS_1'
WEXT: cfg80211-based driver detected
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf flags 0x0
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: 08:11:96:3d:17:90
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
ctrl_interface_group=0
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=16
State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=4):
42 53 5f 31 BS_1
Starting AP scan for specific SSID(s)
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=16
Scan results did not fit - trying larger buffer (8192 bytes)
Received 5422 bytes of scan results (10 BSSes)
BSS: Start scan result update 1
BSS: Add new id 0 BSSID 84:c9:b2:c4:14:03 SSID 'BS_1'
BSS: Add new id 1 BSSID 88:25:2c:d3:7d:e4 SSID 'EasyBox-D37D38'
BSS: Add new id 2 BSSID bc:05:43:42:31:57 SSID 'FRITZ!Box Fon WLAN 7112'
BSS: Add new id 3 BSSID 14:d6:4d:b5:8c:92 SSID 'eichsfeld'
BSS: Add new id 4 BSSID 00:24:fe:ad:17:ed SSID 'Home'
BSS: Add new id 5 BSSID 00:24:01:2a:1c:44 SSID 'MoskitoNetz'
BSS: Add new id 6 BSSID 00:15:0c:e9:ba:b9 SSID 'Aahz'
BSS: Add new id 7 BSSID 00:26:5a:28:01:0c SSID 'JESULEIN-PC_Network'
BSS: Add new id 8 BSSID 00:17:9a:61:bd:79 SSID 'Skinnie@home'
BSS: Add new id 9 BSSID fc:75:16:79:dd:95 SSID 'dlink'
New scan results available
Selecting BSS from priority group 3
Try to find WPA-enabled AP
0: 84:c9:b2:c4:14:03 ssid='BS_1' wpa_ie_len=0 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
1: 88:25:2c:d3:7d:e4 ssid='EasyBox-D37D38' wpa_ie_len=28 rsn_ie_len=24 caps=0x11
skip - SSID mismatch
2: bc:05:43:42:31:57 ssid='FRITZ!Box Fon WLAN 7112' wpa_ie_len=24 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
3: 14:d6:4d:b5:8c:92 ssid='eichsfeld' wpa_ie_len=26 rsn_ie_len=24 caps=0x11
skip - SSID mismatch
4: 00:24:fe:ad:17:ed ssid='Home' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
skip - SSID mismatch
5: 00:24:01:2a:1c:44 ssid='MoskitoNetz' wpa_ie_len=26 rsn_ie_len=24 caps=0x11
skip - SSID mismatch
6: 00:15:0c:e9:ba:b9 ssid='Aahz' wpa_ie_len=24 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
7: 00:26:5a:28:01:0c ssid='JESULEIN-PC_Network' wpa_ie_len=0 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
8: 00:17:9a:61:bd:79 ssid='Skinnie@home' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - no WPA/RSN IE
9: fc:75:16:79:dd:95 ssid='dlink' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
skip - no WPA/RSN IE
Try to find non-WPA AP
0: 84:c9:b2:c4:14:03 ssid='BS_1' wpa_ie_len=0 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
1: 88:25:2c:d3:7d:e4 ssid='EasyBox-D37D38' wpa_ie_len=28 rsn_ie_len=24 caps=0x11
skip - SSID mismatch
2: bc:05:43:42:31:57 ssid='FRITZ!Box Fon WLAN 7112' wpa_ie_len=24 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
3: 14:d6:4d:b5:8c:92 ssid='eichsfeld' wpa_ie_len=26 rsn_ie_len=24 caps=0x11
skip - SSID mismatch
4: 00:24:fe:ad:17:ed ssid='Home' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
skip - SSID mismatch
5: 00:24:01:2a:1c:44 ssid='MoskitoNetz' wpa_ie_len=26 rsn_ie_len=24 caps=0x11
skip - SSID mismatch
6: 00:15:0c:e9:ba:b9 ssid='Aahz' wpa_ie_len=24 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
7: 00:26:5a:28:01:0c ssid='JESULEIN-PC_Network' wpa_ie_len=0 rsn_ie_len=20 caps=0x11
skip - SSID mismatch
8: 00:17:9a:61:bd:79 ssid='Skinnie@home' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
skip - SSID mismatch
9: fc:75:16:79:dd:95 ssid='dlink' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
skip - SSID mismatch
Selecting BSS from priority group 2
Try to find WPA-enabled AP
0: 84:c9:b2:c4:14:03 ssid='BS_1' wpa_ie_len=0 rsn_ie_len=20 caps=0x11
selected based on RSN IE
selected WPA AP 84:c9:b2:c4:14:03 ssid='BS_1'
Trying to associate with 84:c9:b2:c4:14:03 (SSID='BS_1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 2
WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=20
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8c08 len=67
AssocResp IE wireless event - hexdump(len=51): 01 08 82 84 8b 96 12 24 48 6c 32 04 0c 18 30 60 dd 18 00 50 f2 02 01 01 80 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 07 00 0c 43 07 00 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=24
Wireless event: new AP: 84:c9:b2:c4:14:03
Association info event
resp_ies - hexdump(len=51): 01 08 82 84 8b 96 12 24 48 6c 32 04 0c 18 30 60 dd 18 00 50 f2 02 01 01 80 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 07 00 0c 43 07 00 00 00
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=84:c9:b2:c4:14:03
No keys have been configured - skip key clearing
Associated with 84:c9:b2:c4:14:03
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RX EAPOL from 84:c9:b2:c4:14:03
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=2
key_info 0x89 (ver=1 keyidx=0 rsvd=0 Pairwise Ack)
key_length=32 key_data_length=0
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 01
key_nonce - hexdump(len=32): b9 12 4b 27 9c 46 1d a6 6e f8 dc 87 27 7c 92 c5 72 07 77 d7 ab fb 22 bc f6 1d 84 da 9b 7e 08 f5
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 84:c9:b2:c4:14:03 (ver=1)
RSN: msg 1/4 key data - hexdump(len=0):
WPA: Renewed SNonce - hexdump(len=32): b0 58 01 62 69 2a 27 7a 17 0b 74 1f 58 2f 66 33 19 c7 93 52 59 cd 2e 45 27 e0 fa ed c1 b8 1e 85
WPA: PTK derivation - A1=08:11:96:3d:17:90 A2=84:c9:b2:c4:14:03
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
WPA: Sending EAPOL-Key 2/4
RX EAPOL from 84:c9:b2:c4:14:03
IEEE 802.1X RX: version=1 type=3 length=157
EAPOL-Key type=2
key_info 0x13c9 (ver=1 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure Encr)
key_length=32 key_data_length=62
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
key_nonce - hexdump(len=32): b9 12 4b 27 9c 46 1d a6 6e f8 dc 87 27 7c 92 c5 72 07 77 d7 ab fb 22 bc f6 1d 84 da 9b 7e 08 f5
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 79 01 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 2b 36 01 d0 72 81 c5 c5 ac 83 e5 0d 7f 82 3b f1
RSN: encrypted key data - hexdump(len=62): e9 ff f9 25 6e 82 30 7a eb e1 71 cb e1 7d 99 78 69 71 ea 4d 03 bd df 9c ba 80 24 c7 7e c4 33 bc 15 9d 06 84 a6 49 98 de 11 bc 1c 94 7a 29 04 4c ab 83 fd 7e 9d 08 b7 22 cd 7b a6 cb 2b 98
WPA: decrypted EAPOL-Key key data - hexdump(len=62): [REMOVED]
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 84:c9:b2:c4:14:03 (ver=1)
WPA: IE KeyData - hexdump(len=62): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 dd 26 00 0f ac 01 01 00 b4 a3 ec 2a 27 db 02 b0 8d d4 8a 78 0b 3a 85 13 d8 b0 a6 09 be 92 94 4d ec 1f 94 a6 1e 28 9a 7e
WPA: RSN IE in EAPOL-Key - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
WPA: GTK in EAPOL-Key - hexdump(len=40): [REMOVED]
WPA: Sending EAPOL-Key 4/4
WPA: Installing PTK to the driver.
wpa_driver_wext_set_key: alg=2 key_idx=0 set_tx=1 seq_len=6 key_len=32
EAPOL: External notification - portValid=1
State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RSN: received GTK in pairwise handshake - hexdump(len=34): [REMOVED]
WPA: Group Key - hexdump(len=32): [REMOVED]
WPA: Installing GTK to the driver (keyidx=1 tx=0 len=32).
WPA: RSC - hexdump(len=6): 79 01 00 00 00 00
wpa_driver_wext_set_key: alg=2 key_idx=1 set_tx=0 seq_len=6 key_len=32
WPA: Key negotiation completed with 84:c9:b2:c4:14:03 [PTK=TKIP GTK=TKIP]
Cancelling authentication timeout
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-CONNECTED - Connection to 84:c9:b2:c4:14:03 completed (auth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
netlink: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: Supplicant port status: Authorized
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed successfully
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: startWhen --> 0
EAPOL: disable timer tick
|
my supplicant.conf looks like this:
Code: |
#Damit es funktioniert
ctrl_interface=/var/run/wpa_supplicant
#nur root darf WPA konfiguration lesen
ctrl_interface_group=0
#wpa_supplicant soll sich u scannen und AP auswahl kuemmern
ap_scan=1
#eapol_version=1
#fast_reauth=1
network={
ssid="BS_1"
scan_ssid=1
proto=RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="..."
priority=2
}
...
|
I told my Ap to use TKIP and WPA2 only.
under gnome my Networkmanager connect without any problems, so it must work anyway. But i want convert to other lighteweight window-systems, so Networkmanager is no option for me anymore. |
|
Back to top |
|
 |
Royal_ts n00b

Joined: 23 May 2011 Posts: 44 Location: Leipzig
|
Posted: Thu Mar 15, 2012 10:32 am Post subject: |
|
|
by the way:
if my wpa_supplicant.conf looks like this
Code: |
network={
ssid="BS_1"
#scan_ssid=1
#proto=RSN
#key_mgmt=WPA-PSK
#pairwise=CCMP TKIP
#group=CCMP TKIP
psk="..."
#priority=2
}
|
it won't work either |
|
Back to top |
|
 |
Gusar Advocate

Joined: 09 Apr 2005 Posts: 2665 Location: Slovenia
|
Posted: Thu Mar 15, 2012 10:53 am Post subject: |
|
|
That output shows you're connected. So what exactly the problem now? Did you run a dhcp client? |
|
Back to top |
|
 |
d2_racing Bodhisattva


Joined: 25 Apr 2005 Posts: 13047 Location: Ste-Foy,Canada
|
Posted: Thu Mar 15, 2012 11:48 am Post subject: |
|
|
Can you post this :
Code: |
# wpa_cli status
# ifconfig -a
|
|
|
Back to top |
|
 |
Royal_ts n00b

Joined: 23 May 2011 Posts: 44 Location: Leipzig
|
Posted: Thu Mar 15, 2012 3:13 pm Post subject: |
|
|
Thx for your reply!!!!
the first output:
Code: |
localhost linux # wpa_cli status
Selected interface 'wlan0'
bssid=84:c9:b2:c4:14:03
ssid=BS_1
id=0
mode=station
pairwise_cipher=TKIP
group_cipher=TKIP
key_mgmt=WPA2-PSK
wpa_state=COMPLETED
|
and the second one of ifconfig -a
Code: |
...
wlan0 Link encap:Ethernet HWaddr 08:11:96:3d:17:90
inet6 addr: fe80::a11:96ff:fe3d:1790/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2552 errors:0 dropped:0 overruns:0 frame:0
TX packets:2514 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2064732 (1.9 MiB) TX bytes:451002 (440.4 KiB)
|
so it seems to be connected?!
I got also the modules Tkip... modprobe --list:
Code: |
kernel/net/wireless/lib80211_crypt_wep.ko
kernel/net/wireless/lib80211_crypt_ccmp.ko
kernel/net/wireless/lib80211_crypt_tkip.ko
|
I didn't set up a dhcp client. I thought wpa_supplicant would do this. could you pls describe, how to do this?
with kind regards |
|
Back to top |
|
 |
Royal_ts n00b

Joined: 23 May 2011 Posts: 44 Location: Leipzig
|
Posted: Thu Mar 15, 2012 3:15 pm Post subject: |
|
|
The concrete problem is: i can't browse with my browser and the command ping return: unknown host...
The only time, i mentioned dhcp is in /etc/conf.d/net:
Code: |
config_wlan0="dhcp"
|
|
|
Back to top |
|
 |
BillWho Veteran


Joined: 03 Mar 2012 Posts: 1600 Location: US
|
Posted: Fri Mar 16, 2012 4:34 am Post subject: |
|
|
Royal_ts,
You don't have an IP address assigned to your wireless.
gentoo ~ # wpa_cli status
Selected interface 'wlan0'
bssid=58:6d:8f:88:43:45
ssid=wireless_router
id=0
id_str=gentoo
mode=station
pairwise_cipher=TKIP
group_cipher=TKIP
key_mgmt=WPA2-PSK
wpa_state=COMPLETED
ip_address=192.168.1.103
Did you symlink net.wlan0 -> net.lo and add net.wlan0 to your default runlevel? |
|
Back to top |
|
 |
Gusar Advocate

Joined: 09 Apr 2005 Posts: 2665 Location: Slovenia
|
Posted: Fri Mar 16, 2012 9:34 am Post subject: |
|
|
/etc/conf.d/net won't do anything if you're starting wpa_supplicant manually, which you are. Either do everything through the scripts, or do everything manually. |
|
Back to top |
|
 |
Royal_ts n00b

Joined: 23 May 2011 Posts: 44 Location: Leipzig
|
Posted: Fri Mar 16, 2012 10:33 am Post subject: |
|
|
BillWho was right. i didn't start net.wlan0
unfortunately as Gusar said the problem still exists. The behaviour is a bit different:
Code: |
wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -D wext -i wlan0 -d
|
shows me:
Code: |
...
Selecting BSS from priority group 2
Try to find WPA-enabled AP
0: 84:c9:b2:c4:14:03 ssid='BS_1' wpa_ie_len=0 rsn_ie_len=20 caps=0x11
selected based on RSN IE
selected WPA AP 84:c9:b2:c4:14:03 ssid='BS_1'
Trying to associate with 84:c9:b2:c4:14:03 (SSID='BS_1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 2
WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
State: DISCONNECTED -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=20
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=16
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=20
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8c08 len=67
AssocResp IE wireless event - hexdump(len=51): 01 08 82 84 8b 96 12 24 48 6c 32 04 0c 18 30 60 dd 18 00 50 f2 02 01 01 80 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 07 00 0c 43 07 00 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=24
Wireless event: new AP: 84:c9:b2:c4:14:03
Association info event
resp_ies - hexdump(len=51): 01 08 82 84 8b 96 12 24 48 6c 32 04 0c 18 30 60 dd 18 00 50 f2 02 01 01 80 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00 dd 07 00 0c 43 07 00 00 00
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=84:c9:b2:c4:14:03
No keys have been configured - skip key clearing
Associated with 84:c9:b2:c4:14:03
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RX EAPOL from 84:c9:b2:c4:14:03
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=2
key_info 0x89 (ver=1 keyidx=0 rsvd=0 Pairwise Ack)
key_length=32 key_data_length=0
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 01
key_nonce - hexdump(len=32): 19 9d 54 b4 98 11 7e f3 fe d2 4d 23 59 ef a2 78 b4 be 7b 2d 1d fe cb 8a 51 3c 08 44 20 08 00 50
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 84:c9:b2:c4:14:03 (ver=1)
RSN: msg 1/4 key data - hexdump(len=0):
WPA: Renewed SNonce - hexdump(len=32): 81 be ed e0 ef 93 38 2d 1f a5 a8 dc 7e 71 b8 b5 85 ae 9b 9a 0a e8 57 9d fd 5b 70 dc ee 54 8c b2
WPA: PTK derivation - A1=08:11:96:3d:17:90 A2=84:c9:b2:c4:14:03
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00
WPA: Sending EAPOL-Key 2/4
RX EAPOL from 84:c9:b2:c4:14:03
IEEE 802.1X RX: version=1 type=3 length=157
EAPOL-Key type=2
key_info 0x13c9 (ver=1 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure Encr)
key_length=32 key_data_length=62
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
key_nonce - hexdump(len=32): 19 9d 54 b4 98 11 7e f3 fe d2 4d 23 59 ef a2 78 b4 be 7b 2d 1d fe cb 8a 51 3c 08 44 20 08 00 50
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 81 01 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): c4 ee d6 20 eb 65 9e 56 f2 a2 3b 9e 42 36 dc 9e
WPA: Invalid EAPOL-Key MIC when using TPTK - ignoring TPTK
WPA: Could not verify EAPOL-Key MIC - dropping packet
RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=24
Wireless event: new AP: 00:00:00:00:00:00
Disassociation notification
WPA: 4-Way Handshake failed - pre-shared key may be incorrect
Setting scan request: 0 sec 100000 usec
Added BSSID 84:c9:b2:c4:14:03 into blacklist
CTRL-EVENT-DISCONNECTED bssid=84:c9:b2:c4:14:03 reason=0
Disconnect event - remove keys
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
State: 4WAY_HANDSHAKE -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=13):
41 6e 64 72 6f 69 64 41 50 35 30 33 31 AndroidAP5031
Starting AP scan for specific SSID(s)
ioctl[SIOCSIWSCAN]: Device or resource busy
Scan requested (ret=-1) - scan timeout 30 seconds
Failed to initiate AP scan.
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Setting scan request: 1 sec 0 usec
EAPOL: Supplicant port status: Unauthorized
State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=4):
42 53 5f 31 BS_1
Starting AP scan for specific SSID(s)
ioctl[SIOCSIWSCAN]: Device or resource busy
Scan requested (ret=-1) - scan timeout 30 seconds
Failed to initiate AP scan.
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Setting scan request: 1 sec 0 usec
EAPOL: Supplicant port status: Unauthorized
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
ioctl[SIOCSIWSCAN]: Device or resource busy
Scan requested (ret=-1) - scan timeout 30 seconds
Failed to initiate AP scan.
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Setting scan request: 1 sec 0 usec
EAPOL: Supplicant port status: Unauthorized
State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=13):
41 6e 64 72 6f 69 64 41 50 35 30 33 31 AndroidAP5031
Starting AP scan for specific SSID(s)
ioctl[SIOCSIWSCAN]: Device or resource busy
Scan requested (ret=-1) - scan timeout 30 seconds
Failed to initiate AP scan.
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Setting scan request: 1 sec 0 usec
^CCTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
No keys have been configured - skip key clearing
State: DISCONNECTED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Removed BSSID 84:c9:b2:c4:14:03 from blacklist (clear)
BSS: Remove id 9 BSSID 00:26:5a:2f:f8:76 SSID 'Zockerparadies'
BSS: Remove id 10 BSSID 00:1e:58:bc:47:8f SSID 'alberthimapa1'
BSS: Remove id 11 BSSID d8:5d:4c:ba:3d:60 SSID 'infernus'
BSS: Remove id 0 BSSID 84:c9:b2:c4:14:03 SSID 'BS_1'
BSS: Remove id 1 BSSID 88:25:2c:d3:7d:e4 SSID 'EasyBox-D37D38'
BSS: Remove id 4 BSSID bc:05:43:42:31:57 SSID 'FRITZ!Box Fon WLAN 7112'
BSS: Remove id 2 BSSID 00:24:01:39:64:a7 SSID 'bowie'
BSS: Remove id 5 BSSID 00:24:01:39:75:c9 SSID 'A-H_rnchen'
BSS: Remove id 3 BSSID 00:24:fe:ad:17:ed SSID 'Home'
BSS: Remove id 14 BSSID 14:d6:4d:b5:8c:92 SSID 'eichsfeld'
BSS: Remove id 16 BSSID 00:15:0c:e9:ba:b9 SSID 'Aahz'
BSS: Remove id 7 BSSID 7c:4f:b5:87:8c:e4 SSID 'ALICE-WLAN67'
BSS: Remove id 6 BSSID 00:04:0e:db:fe:bb SSID 'FRITZ!Box Fon WLAN 7170'
BSS: Remove id 15 BSSID 00:1e:58:84:9e:69 SSID 'Honigkuchenpferdchen'
BSS: Remove id 8 BSSID 00:1e:58:c6:ea:37 SSID 'ctown'
BSS: Remove id 17 BSSID 5c:d9:98:e1:ec:04 SSID 'leipzig'
BSS: Remove id 18 BSSID 00:24:01:c2:0f:06 SSID 'Macabros'
BSS: Remove id 12 BSSID 00:17:9a:61:bd:79 SSID 'Skinnie@home'
BSS: Remove id 13 BSSID fc:75:16:79:dd:95 SSID 'dlink'
Cancelling scan request
Cancelling authentication timeout
netlink: Operstate: linkmode=0, operstate=6
|
and it won't terminate  |
|
Back to top |
|
 |
Royal_ts n00b

Joined: 23 May 2011 Posts: 44 Location: Leipzig
|
Posted: Fri Mar 16, 2012 1:33 pm Post subject: |
|
|
I just tried a connection with my lan like this:
Code: |
ronny-reiner-rambo royalts # ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:304 errors:0 dropped:0 overruns:0 frame:0
TX packets:304 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:23136 (22.5 KiB) TX bytes:23136 (22.5 KiB)
ronny-reiner-rambo royalts # /etc/init.d/net.eth0 start
* Bringing up interface eth0
* You are using a bash array for config_eth0.
* This feature will be removed in the future.
* Please see net.example for the correct format for config_eth0.
* dhcp ...
* Running dhcpcd ...
dhcpcd[4219]: version 5.2.12 starting
dhcpcd[4219]: eth0: broadcasting for a lease
dhcpcd[4219]: eth0: offered 192.168.0.103 from 192.168.0.1
dhcpcd[4219]: eth0: acknowledged 192.168.0.103 from 192.168.0.1
dhcpcd[4219]: eth0: checking for 192.168.0.103
dhcpcd[4219]: timed out
dhcpcd[4219]: allowing 8 seconds for IPv4LL timeout
dhcpcd[4219]: eth0: leased 192.168.0.103 for 86400 seconds
dhcpcd[4219]: forked to background, child pid 4225 [ ok ]
* received address 192.168.0.103/24 [ ok ]
ronny-reiner-rambo royalts # ifconfig
eth0 Link encap:Ethernet HWaddr b8:70:f4:f5:56:23
inet addr:192.168.0.103 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::ba70:f4ff:fef5:5623/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:27 errors:0 dropped:0 overruns:0 carrier:2
collisions:0 txqueuelen:1000
RX bytes:2420 (2.3 KiB) TX bytes:3428 (3.3 KiB)
Interrupt:50
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:304 errors:0 dropped:0 overruns:0 frame:0
TX packets:304 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:23136 (22.5 KiB) TX bytes:23136 (22.5 KiB)
ronny-reiner-rambo royalts # ping www.google.de
ping: unknown host www.google.de
|
i think this is very interesting. so i cant establish a connection on lan with net.eth0
I followed this tutorial http://www.gentoo.org/doc/en/handbook/handbook-amd64.xml?part=4&chap=1
What the hell is going wrong????
kind of regards |
|
Back to top |
|
 |
BillWho Veteran


Joined: 03 Mar 2012 Posts: 1600 Location: US
|
Posted: Fri Mar 16, 2012 1:51 pm Post subject: |
|
|
Royal_ts,
I had that same problem with the adapters I purchased.
Bus 001 Device 004: ID 0b05:1784 ASUSTek Computer, Inc. USB-N13 802.11n Network Adapter [Ralink RT3072]
What I did to resolve the problem your're now experiencing, following instruction in a README file, was create a directory /etc/Wireless/RT2870STA and copy RT2870STA.dat that I downloaded from their support web site. Although the adapter in now supported in the kernel, that file was still required. Once I created the directory and copied the file everything worked perfectly.
Is it possible that you have a card similar to mine that requires a file to reside somewhere? |
|
Back to top |
|
 |
Gusar Advocate

Joined: 09 Apr 2005 Posts: 2665 Location: Slovenia
|
Posted: Fri Mar 16, 2012 1:57 pm Post subject: |
|
|
You're still mixing up manual and automatic handling that's the hell wrong. Choose one method - either automatic (/etc/conf.d/net and /etc/init.d/net.wlan0) or do things manually. Manually, you first start wpa_supplicant and once it's connected you start a dhcp client. |
|
Back to top |
|
 |
|