i need some help with HUAWEI 303c modem

[GregToo]

I try this setup with usb_modeswitch:(opensuse and ubuntu forum solution)

lsusb

Bus 002 Device 005: ID 12d1:14fe Huawei Technologies


~#leafpad /etc/usb_modeswitch.d/12d1:14fe


########################################################
# Huawei, E353

DefaultVendor= 0x12d1
DefaultProduct=0x14fe

TargetVendor= 0x12d1
TargetProduct=0x1506

CheckSuccess=20

MessageContent="55534243123456780000000000000011062000000100000000000000000000"
########################################################

and udev rule:

~# leafpad /lib/udev/rules.d/40-usb_modeswitch.rules

##################################
# Huawei E353
ATTRS{idVendor}=="12d1", ATTRS{idProduct}=="14fe", RUN+="usb_modeswitch '%b/%k'"
##################################

so.. the result of this is switching TargetProduct ID to 0x150f (CDROM device)

in other words the switch FAIL....the process just change Target Product ID


USB_MODESSWITCH LOG

USB_ModeSwitch log from Wed Aug 21 22:27:16 CLT 2013

Raw args from udev: /2-1.5:1.0

Using global config file: /etc/usb_modeswitch.conf
Using top device dir /sys/bus/usb/devices/2-1.5
Using interface 1.0
----------------
USB values from sysfs:
manufacturer HUAWEI
product HUAWEI Mobile
serial
----------------
bNumConfigurations is 1 - don't check for active configuration
SCSI attributes not needed, moving on
checking config: /usr/share/usb_modeswitch/12d1:14fe
! matched. Reading config data
config: TargetVendor set to 12d1
config: TargetProduct set to 1506
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1

Command to be run:
usb_modeswitch -W -D -s 20 -u -1 -b 2 -g 6 -v 12d1 -p 14fe -f $configBuffer

Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------

Reading long config from command line

* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.5 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)

! PLEASE REPORT NEW CONFIGURATIONS !

DefaultVendor= 0x12d1
DefaultProduct= 0x14fe
TargetVendor= 0x12d1
TargetProduct= 0x1506
TargetClass= not set
TargetProductList=""

DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
MessageEndpoint= not set
MessageContent="55534243123456780000000000000011062000000100000000000000000000"
NeedResponse=0
ResponseEndpoint= not set

InquireDevice disabled
Success check enabled, max. wait time 20 seconds
System integration mode enabled


Use given bus/device number: 002/006 ...
Looking for default devices ...
bus/device number matched
searching devices, found USB ID 12d1:14fe
found matching vendor ID
found matching product ID
adding device
Found device in default mode, class or configuration (1)
Skipping the check for the current configuration
Using interface number 0
Using endpoints 0x01 (out) and 0x81 (in)

USB description data (for identification)
-------------------------
Manufacturer: HUAWEI
Product: HUAWEI Mobile
Serial No.: not provided
-------------------------
Looking for active driver ...
OK, driver found; name unknown, limitation of libusb1
OK, driver "unkown" detached
Setting up communication with interface 0
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
libusb: 0.000000 error [op_clear_halt] clear_halt failed error -1 errno 71
libusb: 0.004239 error [op_clear_halt] clear_halt failed error -1 errno 71
libusb: 0.204327 error [op_release_interface] release interface failed, error -1 errno 22
OK, message successfully sent
Resetting response endpoint 0x81
Could not reset endpoint (probably harmless): -34
Resetting message endpoint 0x01
Could not reset endpoint (probably harmless): -34
Device is gone, skipping any further commands
Bus/dev search active, referring success check to wrapper. Bye.

ok:busdev
--------------------------------
(end of usb_modeswitch output)

Checking success of mode switch for max. 20 seconds ...
Waiting for device file system (1 sec.) ...
Waiting for device file system (2 sec.) ...
Waiting for device file system (3 sec.) ...
Waiting for device file system (4 sec.) ...
Waiting for device file system (5 sec.) ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...

Target config not matching - current values are
2-1.5:1.0/bInterfaceClass: ff
bConfigurationValue: 1
bNumConfigurations: 1
busnum: 2
devnum: 7
idProduct: 150f
idVendor: 12d1
manufacturer: HUAWEI
product: HUAWEI Mobile
serial:

Mode switching may have failed. Exiting


I play with gentoo BOX
with usb_modeswitch 1.2.5_p20121109 and kernel 3.8.13

any suggestion thanksss